Introduction
A washing machine that won’t drain is a common and frustrating problem. It means you can’t get your clothes out, and you risk water damage to your laundry area. If your Kenmore washer is not draining, it’s essential to address the issue quickly to prevent further complications like mold growth or electrical hazards. Often, the problem can be resolved with simple troubleshooting steps, saving you the cost of a repair technician. Explore more in our Washing Machine Problems 4 collection.
💡 Technical Key Takeaways:
- Core Focus: Diagnostic schematic and terminal connection layout for My Kenmore Washer Is Not Draining.
- Target Scope: Field technicians, automotive DIYers, and residential/commercial electricians.
- Safety Rule: Always disconnect the primary power source/battery terminal and verify zero voltage with a multimeter before touching wires.
Common Causes of My Kenmore Washer is Not Draining
Several factors can prevent your Kenmore washer from draining correctly. Here are some of the most common causes:. For more related activities, check out our Kenmore Washer Not Draining Properly.
- Clogged Drain Hose: The drain hose can become blocked with lint, small objects (like socks!), or debris.
- Clogged Drain Pump Filter: Many Kenmore washers have a filter to catch lint and debris before they reach the drain pump. This filter can become clogged.
- Kinked or Twisted Drain Hose: A kink or twist in the drain hose can restrict water flow.
- Faulty Drain Pump: The drain pump is responsible for pushing the water out of the washer. If it fails, the washer won’t drain.
- Clogged Drainpipe: The drainpipe where the washer hose connects could be clogged.
- Air Lock in the Drain Hose: Sometimes, air trapped in the drain hose can prevent proper drainage.
- Lid Switch Malfunction: If the lid switch (which tells the washer the lid is closed) is faulty, the washer may not enter the drain cycle.
- Control Panel Issue: Although less common, a problem with the washer’s control panel can prevent the drain cycle from initiating.
Symptoms Checklist
Use this checklist to confirm the “washer not draining” issue:
- Water remains in the washing machine drum after the cycle completes.
- You hear a humming or buzzing sound during the drain cycle, but no water is being pumped out.
- The washer displays an error code related to draining. (Check your owner’s manual for specific codes).
- The drain hose is visibly kinked or blocked.
- The washing machine won’t start the spin cycle.
How to Fix My Kenmore Washer is Not Draining Step-by-Step Guide
Follow these steps to troubleshoot your Kenmore washer:
- Unplug the Washer: For safety, always unplug the washing machine from the electrical outlet before starting any troubleshooting.
- Inspect the Drain Hose: Check the entire length of the drain hose for kinks, twists, or obstructions. Straighten any kinks and ensure the hose isn’t crushed.
- Check the Drain Hose Connection: Disconnect the drain hose from the drainpipe. Check for any clogs at the connection point.
- Clear the Drainpipe: Run water into the drainpipe to ensure it’s clear. If it’s clogged, use a drain snake or plumber’s auger to remove the blockage.
- Locate the Drain Pump Filter: Refer to your Kenmore washer’s owner’s manual to find the drain pump filter. It’s usually located at the front, bottom of the machine, behind a small access panel.
- Clean the Drain Pump Filter: Open the access panel, and carefully remove the filter. Clean away any lint, hair, or debris. Rinse the filter thoroughly.
- Inspect the Drain Pump: With the filter removed, check the drain pump impeller (the small fan inside the pump housing). Make sure it spins freely and isn’t blocked by anything.
- Check for Air Lock: Reattach the drain hose loosely to the drainpipe. Run a short drain/spin cycle. This may help dislodge an air lock.
- Test the Lid Switch: Manually depress the lid switch (usually located near the lid hinge) to see if the washer starts the spin cycle. Be careful! Do not bypass the switch permanently. If the washer starts when you press the switch, the switch might be faulty.
- Check the Error Code (if applicable): If your washer displays an error code, consult your owner’s manual to identify the code’s meaning and recommended solutions.
- Reset the Washer: Some washers can be reset by unplugging them for 1-2 minutes and then plugging them back in. This can sometimes clear minor electronic glitches.
- Level the Washer: An unbalanced washer can sometimes have draining issues. Ensure the washer is level using a level tool. Adjust the leveling feet at the bottom of the machine as needed.
Fix the Issue Without Buying Parts
Often, the issue can be resolved without needing to replace any parts:
- Regular Cleaning: Clean the drain pump filter every few months to prevent clogs.
- Use Less Soap: Excessive soap can contribute to lint buildup. Use the recommended amount of detergent.
- Inspect Hoses Regularly: Periodically check the drain hose and inlet hoses for any signs of damage or wear.
- Run Empty Cleaning Cycles: Run an empty washer cycle with a washing machine cleaner every few months to remove buildup.
When Replacement Might Be Necessary
If you’ve tried all the troubleshooting steps and your Kenmore washer still isn’t draining, the drain pump itself may be faulty and require replacement. A new drain pump can cost between $50 and $150 USD. Other parts that could potentially fail include the lid switch ($20-$50 USD) or, in rare cases, the control board ($100-$300 USD). Before replacing any parts, consider having a qualified appliance repair technician diagnose the problem to ensure you’re replacing the correct component. Discover more free resources across our collection library.
Safety Warning
- Always unplug the washing machine before performing any maintenance or repairs.
- Be careful when dealing with water and electricity. Avoid working on the washer with wet hands or standing in water.
- If you’re uncomfortable performing any of these steps, consult a qualified appliance repair technician.
Tools You May Need
- Screwdrivers (Phillips and flathead)
- Pliers
- Bucket or container to catch water
- Towel or rags
- Drain snake or plumber’s auger
- Level
FAQ
Here are some frequently asked questions about Kenmore washer draining issues:
- Q: Why is my washer making a humming noise but not draining? A: This often indicates a blockage in the drain pump or a failing drain pump motor.
- Q: How often should I clean the drain pump filter? A: Ideally, clean it every 2-3 months, or more frequently if you wash heavily soiled clothes often.
- Q: Can I use bleach to clean the drain hose? A: It’s not recommended. Bleach can damage the rubber hose over time. Use a specialized washing machine cleaner instead.
- Q: My washer is displaying an “LE” or “E20” error code. What does that mean? A: These codes often indicate a draining issue. Consult your owner’s manual for specific troubleshooting steps for these codes.
Conclusion
Troubleshooting a Kenmore washer that won’t drain can seem daunting, but by following these steps, you can often resolve the issue yourself. Start with the simple fixes like checking the drain hose and cleaning the filter. If you’re still experiencing problems after trying these steps, it may be time to consult a qualified appliance repair technician. Don’t give up before trying the DIY solutions first!
Youtube Video:
Quick Wiring Specifications & Terminal Guide
| Component / Circuit | Standard Wire Gauge | Recommended Protection |
|---|---|---|
| Control & Trigger Signals | 18 – 20 AWG | 5A – 7.5A Inline Fuse |
| Standard Auxiliary Load | 14 – 16 AWG | 15A – 20A Circuit Breaker |
| Main Power Feed / Supply | 10 – 12 AWG | 30A – 40A Heavy-Duty Relay |
