Whirlpool Washer Clicking Not Spinning


Whirlpool Washer Clicking Not Spinning

Introduction

That awful clicking sound coming from your Whirlpool washer accompanied by clothes that are soaking wet is a frustrating problem! When your washer clicks but refuses to spin, it means the motor isn’t engaging to rotate the drum. This is a common issue that can happen after a heavy load, or simply with the passage of time. Addressing this promptly prevents further damage to your washing machine and saves you from wearing damp clothes. Ignoring the problem can lead to a complete breakdown, so let’s troubleshoot!. Explore more in our Washing Machine Problems 6 collection.

💡 Technical Key Takeaways:

  • Core Focus: Diagnostic schematic and terminal connection layout for Whirlpool Washer Clicking Not Spinning.
  • Target Scope: Field technicians, automotive DIYers, and residential/commercial electricians.
  • Safety Rule: Always disconnect the primary power source/battery terminal and verify zero voltage with a multimeter before touching wires.

Common Causes of whirlpool washer clicking not spinning

Here are some of the most likely reasons your Whirlpool washer is clicking and refusing to spin:

  • Overloaded Washer: Too many clothes can prevent the motor from starting the spin cycle.
  • Lid Switch Malfunction: The lid switch prevents spinning when the lid is open. If faulty, it may prevent spinning even when closed.
  • Drive Belt Issues: A worn, loose, or broken drive belt is a common cause.
  • Motor Coupling Failure: This part connects the motor to the transmission. It’s designed to break under stress to protect the motor and transmission, so it often fails.
  • Worn Motor: After years of use, the motor itself may be failing.
  • Drainage Problem: If the washer hasn’t fully drained, it won’t spin. A clogged drain hose or pump can be the culprit.
  • Faulty Timer or Control Board: The electronic components that control the spin cycle might have issues.
  • Foreign Object Obstruction: Small objects like coins or socks can get stuck between the tubs, preventing spinning.
  • Worn Clutch: A worn clutch will cause the machine not to engage into the spin cycle.

Symptoms Checklist

Check for these signs to accurately diagnose the problem:

  • Clicking sound heard during the spin cycle.
  • Washer drum does not spin, clothes remain wet.
  • Washer hums but doesn’t spin.
  • Error code displayed on the control panel (check your user manual).
  • Washer tub fills with water, but doesn’t drain.
  • Burning smell during operation.
  • The washer lid lock light is flashing.

How to Fix whirlpool washer clicking not spinning Step-by-Step Guide

Follow these steps to troubleshoot your washing machine:

  1. Unplug the Washer: Safety first! Disconnect the power cord from the outlet before starting any repairs.
  2. Check for Overloading: Remove some items from the washer if you suspect it’s overloaded. Try running a spin cycle with a smaller load.
  3. Inspect the Lid Switch: The lid switch is usually located under the lid. Check if it’s clean and moves freely. You can gently press it with your finger to see if it clicks. If it seems loose or broken, it might need replacement (later step).
  4. Check the Drain Hose: Make sure the drain hose isn’t kinked, clogged, or blocked. Disconnect it from the drainpipe and inspect it.
  5. Check the Drain Pump: The drain pump is usually located at the bottom of the washer cabinet. Check for any obstructions like lint or small objects. You might be able to access it from the back panel. Clean it if necessary.
  6. Inspect the Drive Belt: You’ll need to access the inside of the washer. Open the back panel of the washer to see the drive belt connecting the motor to the drum. Check if it’s cracked, loose, or broken.
  7. Check the Motor Coupling: Located between the motor and the transmission. If it’s broken, you’ll see signs of wear or cracks in the component.
  8. Listen to the motor. After the drum is manually spun by hand, listen to any unusual noise coming from the motor. If so, have it checked by a technician.
  9. Check for Obstructions in the Tub: Inspect the space between the inner and outer tubs for any trapped objects. You might need to remove some parts to gain access.
  10. Consult Your User Manual: Check your user manual for specific troubleshooting steps or error codes.
  11. Run a Calibration Cycle (if applicable): Some Whirlpool washers have a calibration cycle that can reset the motor and control board. Check your manual for instructions.

Fix the Issue Without Buying Parts

Before spending money on parts, try these free solutions:

  • Washer Reset: Unplug the washer for 1-2 minutes, then plug it back in. This can sometimes reset the control board.
  • Cleaning: Clean the drain hose and pump to remove any obstructions.
  • Recalibration: Run a calibration cycle as mentioned in the user manual.
  • Inspection Tips: Visually inspect all components for any signs of damage or wear.
  • Maintenance Basics: Avoid overloading the washer and regularly clean the lint filter.

When Replacement Might Be Necessary

If the above steps don’t resolve the issue, some parts might need replacing. Here are a few:

  • Lid Switch: $15-$30
  • Drive Belt: $10-$20
  • Motor Coupling: $15-$25
  • Drain Pump: $40-$80
  • Motor: $100-$300. If the motor needs replacing, it is usually better to get a new machine.

Safety Warning

  • Always unplug the washer before attempting any repairs.
  • Avoid working on the washer while it’s connected to a water source.
  • Be careful when handling sharp tools or removing parts.
  • Wipe up any spills to prevent slipping.
  • If you’re uncomfortable with any of these steps, consult a qualified appliance repair technician.

Tools You May Need

  • Screwdrivers (Phillips and flathead)
  • Pliers
  • Wrench
  • Shop Towels
  • Flashlight
  • Gloves

FAQ

Here are some frequently asked questions about this issue:

  • Q: Why is my washer clicking even when empty? A: The clicking sound when empty is often related to a faulty motor coupling or a worn drive belt.
  • Q: How do I know if my lid switch is bad? A: If the washer won’t spin even when the lid is closed, the lid switch might be faulty. You can test it with a multimeter, but you can usually see the broken clip.
  • Q: Can I replace the drive belt myself? A: Yes, replacing the drive belt is a relatively simple repair.
  • Q: My washer is making a loud humming noise but not spinning. What could it be? A: This is often a sign of a motor issue or an obstruction preventing the drum from turning.
  • Q: How often should I clean my washing machine’s drain pump? A: It’s recommended to clean the drain pump every 3-6 months, depending on usage.
  • Q: Where is the drain pump located at? A: Usually located at the bottom, toward the back of the machine.

Conclusion

Troubleshooting a “Whirlpool washer clicking not spinning” issue can seem daunting, but by following these steps, you can often diagnose and fix the problem yourself. Don’t be afraid to get your hands dirty! However, if you’re uncomfortable with any of these repairs or if the problem persists, don’t hesitate to call a qualified appliance repair technician. You’ve got this!

Youtube Video:


Quick Wiring Specifications & Terminal Guide

Component / Circuit Standard Wire Gauge Recommended Protection
Control & Trigger Signals 18 – 20 AWG 5A – 7.5A Inline Fuse
Standard Auxiliary Load 14 – 16 AWG 15A – 20A Circuit Breaker
Main Power Feed / Supply 10 – 12 AWG 30A – 40A Heavy-Duty Relay

Images References


Images References, Washing Machine Problems 6

📚 Related Articles

Scroll to Top