Samsung Washing Machine Fills With Water Then Stops

Introduction

It’s frustrating when your Samsung washing machine starts filling with water but then suddenly stops. This issue can disrupt your laundry routine and leave you with soaking wet clothes. Addressing this problem quickly is important to prevent potential water damage to your home and to get your washing machine back in working order. This guide will walk you through common causes and troubleshooting steps to help you resolve the issue yourself.

Common Causes of Samsung Washing Machine Fills with Water Then Stops

Here are some of the most frequent reasons why your Samsung washing machine might be filling with water and then stopping:. For more related activities, check out our Samsung Washer No Drain.

• Low Water Pressure: Insufficient water pressure from your home’s supply can prevent the washer from filling completely, causing it to stop mid-fill.
• Blocked Water Inlet Hoses: Mineral deposits or debris can clog the inlet hoses, restricting water flow.
• Faulty Water Inlet Valve: This valve controls the flow of water into the machine. If it’s malfunctioning, it might not open or close properly, leading to interrupted filling.
• Clogged Drain Hose: If the drain hose is clogged, the washer might sense an issue and stop filling to prevent overflow.
• Air Lock in Drain Hose: Similar to clogged drain hose, an air lock in the drain hose can signal an overflow issue.
• Defective Water Level Sensor: This sensor tells the machine when the water level is correct. If it’s faulty, it might send an incorrect signal, causing the washer to stop filling prematurely.
• Problem with the Lid Switch/Door Lock: If the machine doesn’t detect that the lid or door is properly closed, it may interrupt the filling process.
• Control Board Malfunction: In rare cases, a problem with the washing machine’s control board can cause erratic behavior, including stopping the fill cycle.

Symptoms Checklist

Use this checklist to confirm the problem:

• Washing machine starts filling, then stops abruptly.
• Error code appears on the display screen (note the code).
• Water is barely trickling into the machine.
• You hear a buzzing sound from the water inlet valve area.
• The washing machine door/lid is difficult to lock or unlock.

How to Fix Samsung Washing Machine Fills with Water Then Stops Step-by-Step Guide

Follow these steps to troubleshoot the problem:

1. Check Water Supply: Make sure both hot and cold water supply valves are fully open.
2. Inspect Water Inlet Hoses: Disconnect the hoses from the back of the washing machine and check for kinks, bends, or obstructions. Straighten any kinks.
3. Clean Water Inlet Hoses: Flush the hoses with water to remove any sediment or debris.
4. Clean Water Inlet Valve Screens: Locate the small screens where the hoses connect to the water inlet valves. Remove the screens and clean them thoroughly with a brush.
5. Check Water Pressure: Connect a hose to the water supply valve and check the water pressure. It should be adequate (consult your local water authority if unsure).
6. Inspect the Drain Hose: Make sure the drain hose is not kinked or clogged. Remove the drain hose and flush it out. Also check if the drain pipe is clogged.
7. Air Lock: Check the end of the drain hose and make sure it’s not too far down into the drain pipe. It should be high enough to prevent siphoning and air locks.
8. Check Lid Switch/Door Lock: Ensure the lid or door closes and locks properly. Visually inspect the switch for damage.
9. Reset the Washing Machine: Unplug the washing machine for 1-2 minutes, then plug it back in. This can sometimes reset the control board.
10. Run a Calibration Cycle (if available): Consult your user manual to see if your model has a calibration cycle. This can help the machine relearn its settings.
11. Check the Water Level Sensor Hose: Locate the water level sensor hose (usually a small tube connected to the pressure switch). Ensure it’s not kinked, blocked, or disconnected.
12. Look for Error Codes: Consult your washing machine’s manual to identify the error code and its corresponding troubleshooting steps.

Fix the Issue Without Buying Parts

Before resorting to replacements, try these free and easy methods:

• Reset the Washing Machine: As mentioned above, unplugging and plugging back in the machine can often resolve minor glitches.
• Cleaning: Regularly clean the detergent dispenser, drum, and door seal to prevent build-up that could affect performance.
• Recalibration: If your model supports it, running a recalibration cycle can help the machine optimize its water levels and other settings.
• Visual Inspection: Thoroughly inspect all hoses and connections for any signs of damage, leaks, or blockages.
• Proper Maintenance: Use the correct amount of detergent and avoid overloading the machine to prevent strain and potential issues.

When Replacement Might Be Necessary

If you’ve tried all the troubleshooting steps and the washing machine still isn’t working correctly, you might need to consider replacing a part. Common parts that fail and cause this issue include the water inlet valve (estimated cost: $30-$70), the water level sensor ($20-$50), and in rare cases, the control board (can be expensive, $100-$300). Consider contacting a qualified appliance repair technician before replacing the control board.

Safety Warning

• Always unplug the washing machine from the power outlet before performing any repairs.
• Turn off the water supply to the washing machine before disconnecting any hoses.
• Be careful when handling water; mop up any spills to prevent slips and falls.
• If you are not comfortable performing repairs yourself, consult a qualified appliance repair technician.

Tools You May Need

• Screwdrivers (Phillips and flathead)
• Pliers
• Adjustable wrench
• Bucket
• Towels
• Small brush (e.g., toothbrush)

FAQ

Here are some frequently asked questions:

• Q: My washing machine stops filling and displays an error code. What should I do?
  A: Consult your user manual to identify the error code and follow the recommended troubleshooting steps.
• Q: How do I know if my water inlet valve is faulty?
  A: If you hear a buzzing sound but no water is flowing, or if the valve doesn’t shut off completely, it might be faulty.
• Q: Can low water pressure cause this issue?
  A: Yes, low water pressure can prevent the washing machine from filling completely, causing it to stop.
• Q: How often should I clean the water inlet valve screens?
  A: It’s recommended to clean them every 6 months, or more frequently if you have hard water.

Conclusion

Troubleshooting a Samsung washing machine that fills with water and then stops can seem daunting, but by following these steps, you can often identify and resolve the issue yourself. Remember to prioritize safety and take your time. If you’ve exhausted all options and are still experiencing problems, don’t hesitate to contact a qualified appliance repair technician for assistance.

Youtube Video: