Old Kenmore Washer Not Draining


Old Kenmore Washer Not Draining

Introduction

Is your old Kenmore washing machine refusing to drain? A washer full of water after a wash cycle is a frustrating problem that can lead to mold growth and even water damage. Addressing this issue quickly is important to avoid further complications. This guide will walk you through the most common causes of a Kenmore washer not draining and provide simple, step-by-step troubleshooting instructions. Explore more in our Washing Machine Problems 2 collection.

💡 Technical Key Takeaways:

  • Core Focus: Diagnostic schematic and terminal connection layout for Old Kenmore Washer Not Draining.
  • Target Scope: Field technicians, automotive DIYers, and residential/commercial electricians.
  • Safety Rule: Always disconnect the primary power source/battery terminal and verify zero voltage with a multimeter before touching wires.

Common Causes of Old Kenmore Washer Not Draining

Here are some frequent reasons why your Kenmore washer might be holding water:

  • Clogged Drain Hose: A kinked or blocked drain hose restricts water flow.
  • Clogged Drain Pump Filter: Debris like lint, socks, or buttons can obstruct the drain pump filter.
  • Faulty Drain Pump: The pump might be malfunctioning and unable to force water out.
  • Kinked or Blocked Tub-to-Pump Hose: This hose connects the tub to the drain pump; obstructions here prevent drainage.
  • Air Lock in Drain Hose: Trapped air can prevent the pump from functioning correctly.
  • Defective Lid Switch: If the lid switch isn’t working, the washer may not enter the drain cycle.
  • Control Board Issue: In some cases, a faulty control board might prevent the drain cycle from initiating.
  • Overuse of Soap: Excessive suds can overwhelm the drain pump.

Symptoms Checklist

Here’s how to tell if your Kenmore washer is having draining problems:

  • Washer tub is full of water after a completed wash cycle.
  • The washer makes a humming noise but doesn’t drain.
  • Error code related to draining appears on the washer’s display (if applicable).
  • Water drains very slowly.
  • The drain hose appears kinked or damaged.

How to Fix Old Kenmore Washer Not Draining Step-by-Step Guide

Follow these steps to troubleshoot your Kenmore washer:

  1. Unplug the Washer: Always disconnect the power supply before working on any appliance.
  2. Inspect the Drain Hose: Locate the drain hose (usually at the back of the washer). Check for kinks, bends, or obstructions. Straighten any kinks and ensure the hose isn’t crushed.
  3. Detach and Clear the Drain Hose: Disconnect the drain hose from both the washer and the drainpipe. Flush it with water to dislodge any blockages. A garden hose can be helpful for this.
  4. Locate the Drain Pump Filter: The location varies by model, but it’s often behind a small access panel at the front bottom of the washer. Consult your user manual for the exact location.
  5. Drain Remaining Water: Place a shallow pan or towels under the access panel to catch any water that spills out when you remove the filter.
  6. Clean the Drain Pump Filter: Carefully remove the drain pump filter and clean it thoroughly. Remove any lint, hair, buttons, or other debris.
  7. Inspect the Drain Pump: With the filter removed, look inside the pump housing. Check for any visible obstructions. You might be able to reach in with pliers to remove larger items.
  8. Check the Tub-to-Pump Hose: If accessible, inspect the hose connecting the tub to the drain pump for kinks or blockages.
  9. Check the Lid Switch: The lid switch tells the washer the lid is closed, allowing it to spin and drain. Gently press the switch with your finger. If it doesn’t click or feels loose, it might be faulty. (Note: Replacing this switch may require some disassembly.)
  10. Check for Air Lock: Sometimes, an air lock in the drain hose can prevent draining. Try lowering the drain hose to the floor to see if the water starts draining by gravity. Then, lift the hose back into its normal position.
  11. Run a Test Cycle: After cleaning and inspecting, plug the washer back in and run a short spin cycle to see if it drains properly.
  12. Reduce Soap Usage: Excessive soap can create too many suds, hindering the drain pump. Use only the recommended amount of HE (High Efficiency) detergent.

Fix the Issue Without Buying Parts

Here are some solutions you can try without replacing anything:

  • Reset the Washer: Unplug the washer for a few minutes, then plug it back in. This can sometimes reset the control board and clear error codes.
  • Clean the Washer: Run an empty wash cycle with a washing machine cleaner to remove buildup and residue that can clog the drain.
  • Check Installation: Make sure the drain hose is properly installed and not inserted too far into the drain pipe, which can cause siphoning.
  • Maintenance Basics: Regularly clean the lint trap and drain pump filter to prevent future clogs.

When Replacement Might Be Necessary

If you’ve tried all the troubleshooting steps and your Kenmore washer still isn’t draining, the drain pump might be faulty and require replacement. A new drain pump can cost anywhere from $50 to $150, depending on the model. A faulty control board is another possibility, but it’s less common. Control boards can be expensive, ranging from $100 to $300. Replacing the lid switch is a more affordable option usually under $50.

Safety Warning

  • Always unplug the washer from the power outlet before performing any repairs.
  • Be careful when handling water to avoid slips and falls. Clean up any spills immediately.
  • Do not attempt repairs beyond your skill level. If you’re unsure, consult a qualified appliance repair technician.

Tools You May Need

  • Screwdrivers (Phillips and flathead)
  • Pliers
  • Bucket or shallow pan
  • Towels
  • Flashlight
  • Garden hose (optional, for flushing drain hose)

FAQ

Here are some common questions about washer draining problems:

  • Q: Why is my washer making a humming noise but not draining? A: This often indicates a blockage in the drain pump or a failing drain pump motor.
  • Q: How often should I clean the drain pump filter? A: Clean the drain pump filter every 1-3 months, depending on usage.
  • Q: Can I use Drano to unclog my washer drain? A: No, Drano and other chemical drain cleaners can damage the washer’s internal components.
  • Q: What does HE detergent mean? A: HE stands for High Efficiency. HE detergent is specially formulated for use in high-efficiency washers that use less water. Using regular detergent in an HE washer can cause excessive suds and draining problems.

Conclusion

Troubleshooting a Kenmore washer that won’t drain can seem daunting, but by following these steps, you can often resolve the issue yourself. Remember to prioritize safety and take your time. If you’ve exhausted all the DIY options and your washer still isn’t draining, it might be time to call a qualified appliance repair technician. Good luck!. Discover more free resources across our collection library.

Youtube Video:


Quick Wiring Specifications & Terminal Guide

Component / Circuit Standard Wire Gauge Recommended Protection
Control & Trigger Signals 18 – 20 AWG 5A – 7.5A Inline Fuse
Standard Auxiliary Load 14 – 16 AWG 15A – 20A Circuit Breaker
Main Power Feed / Supply 10 – 12 AWG 30A – 40A Heavy-Duty Relay

Images References


Images References, Washing Machine Problems 2

📚 Related Articles

Scroll to Top