Maytag Washer Won T Stop Draining


Maytag Washer Won T Stop Draining

Introduction

Discovering that your Maytag washer won’t stop draining can be frustrating and a bit alarming. It means your laundry cycle is interrupted, water is being wasted, and you’re likely facing a potential mess. This usually happens mid-cycle or even when the washer is off. Addressing this promptly is important to prevent water damage to your floors and to save on your water bill. A washer constantly draining indicates a problem that needs immediate attention to prevent further issues.

💡 Technical Key Takeaways:

  • Core Focus: Diagnostic schematic and terminal connection layout for Maytag Washer Won T Stop Draining.
  • Target Scope: Field technicians, automotive DIYers, and residential/commercial electricians.
  • Safety Rule: Always disconnect the primary power source/battery terminal and verify zero voltage with a multimeter before touching wires.

Common Causes of Maytag Washer Won’t Stop Draining

Here are some of the most common reasons why your Maytag washer might be continuously draining:

  • Drain Hose Issues: A drain hose that is inserted too far into the drainpipe or is kinked can cause a siphoning effect.
  • Clogged Drain Pump: Debris like lint, small clothing items, or hair can clog the drain pump, preventing it from closing properly.
  • Faulty Drain Valve: The drain valve (or drain solenoid) might be stuck open due to wear and tear or debris.
  • Siphonage: If the drain hose is positioned too low, gravity can cause a constant siphon, pulling water out of the washer.
  • Pressure Switch Problems: A malfunctioning pressure switch might not be signaling the washer to stop draining.
  • Control Board Malfunction: In rare cases, the electronic control board might be sending incorrect signals to the drain pump or valve.
  • Air Admittance Valve (AAV) Clog: If your drainpipe has an AAV, it might be clogged preventing proper air intake and causing siphoning.
  • Drain Height Incorrect The standpipe that the drain hose feeds into may be too low.

Symptoms Checklist

Use this checklist to accurately identify the issue:

  • Washer continuously drains even when turned off.
  • Water drains slowly or only a small amount at a time.
  • The washer fills with water, but immediately starts draining.
  • The “drain” light is illuminated on the control panel, even when it shouldn’t be.
  • You hear the drain pump running constantly.
  • Error codes related to draining are displayed on the washer’s screen.

How to Fix Maytag Washer Won’t Stop Draining Step-by-Step Guide

Follow these steps to troubleshoot and potentially fix your draining issue:

  1. Unplug the Washer: For safety, always disconnect the washer from the power outlet before starting any repairs.
  2. Inspect the Drain Hose: Check for kinks, bends, or clogs in the drain hose. Straighten any kinks and ensure the hose isn’t crushed.
  3. Check Drain Hose Insertion: Make sure the drain hose isn’t inserted too far into the drainpipe. Typically, it should extend no more than 6-8 inches.
  4. Verify Drain Hose Height: The top of the drain hose should be higher than the maximum water level in the washer tub. Consult your owner’s manual for the recommended height, but it’s typically around 30-36 inches.
  5. Clean the Drain Pump Filter: Locate the drain pump (usually at the bottom front or back of the washer behind an access panel). Open the access panel and remove the drain pump filter. Clean any lint, hair, or debris from the filter.
  6. Inspect the Drain Pump: After cleaning the filter, visually inspect the drain pump for any obstructions. You can also try manually spinning the pump impeller to ensure it moves freely.
  7. Check the Drain Valve (if accessible): If you can access the drain valve (solenoid), inspect it for any signs of damage or debris. Try to manually move the valve to see if it’s stuck.
  8. Check Air Admittance Valve (AAV): If you have one on your drainpipe, make sure it is not clogged.
  9. Run a Calibration Cycle (if available): Some Maytag washers have a calibration cycle that can help reset the control board and resolve minor issues. Check your owner’s manual for instructions on how to run a calibration cycle.
  10. Check the Standpipe Height: Ensure the standpipe (the pipe where the drain hose goes) is the proper height, typically between 30 and 96 inches.
  11. Test the Pressure Switch Hose: Locate the pressure switch and its connected hose. Disconnect the hose and blow into it gently. You should hear a click from the switch. If not, the switch might be faulty. (Note: this may require disassembly, proceed with caution).
  12. Look for a Siphon Break: You can install a siphon break on the drain hose to prevent siphoning, especially if you have a low drain.

Fix the Issue Without Buying Parts

Before considering replacing any parts, try these free methods:

  • Reset the Washer: Unplug the washer for 1-2 minutes, then plug it back in. This can sometimes reset the electronic controls.
  • Deep Cleaning: Run a washer cleaning cycle with a washing machine cleaner to remove any buildup that might be affecting the drain valve or pump.
  • Recalibration: If your washer has a calibration cycle, run it.
  • Inspection Tips: Use a flashlight to thoroughly inspect the drain pump area for any hidden debris.
  • Maintenance Basics: Regularly clean the lint filter after each load to prevent clogs.

When Replacement Might Be Necessary

If you’ve tried all the troubleshooting steps and your washer still won’t stop draining, it might be time to consider replacing a part. Common parts that fail include:

  • Drain Pump: If the pump is damaged or the impeller is broken, it will need to be replaced. (Estimated cost: $50-$150 USD)
  • Drain Valve (Solenoid): If the valve is stuck open or damaged, it needs to be replaced. (Estimated cost: $30-$80 USD)
  • Pressure Switch: If the pressure switch is faulty, it may not be signaling the washer to stop draining. (Estimated cost: $20-$60 USD)
  • Control Board: In rare cases, the control board may be faulty. This is usually a last resort replacement due to the higher cost. (Estimated cost: $100-$300 USD)

Safety Warning

  • Always unplug the washer from the power outlet before attempting any repairs.
  • Be careful when working around water and electrical components to avoid electric shock.
  • Wear gloves to protect your hands from sharp edges and debris.
  • Clean up any water spills immediately to prevent slips and falls.

Tools You May Need

  • Screwdrivers (Phillips and flathead)
  • Pliers
  • Flashlight
  • Bucket or towels to catch water
  • Gloves

FAQ

Here are some frequently asked questions about washers that won’t stop draining:

  • Q: Why is my washer draining even when it’s off?

    A: This is often due to a siphoning effect, a faulty drain valve, or a clogged drain pump.

  • Q: How do I know if my drain pump is clogged?

    A: If you hear a loud humming noise during the drain cycle or the washer drains very slowly, the drain pump is likely clogged.

  • Q: Can I fix this myself, or do I need a professional?

    A: Many of the common causes can be fixed with basic troubleshooting. If you’re not comfortable working with electrical appliances, it’s best to call a professional.

  • Q: How often should I clean my washer’s drain pump filter?

    A: Ideally, you should clean the drain pump filter every 1-3 months, depending on how frequently you use your washer.

Conclusion

A Maytag washer that won’t stop draining can be a nuisance, but with a systematic approach, you can often identify and resolve the issue yourself. Start with the simplest solutions, such as checking the drain hose and cleaning the drain pump filter. If the problem persists, consider inspecting the drain valve and pressure switch. By following these steps, you can potentially save yourself the cost of a service call. However, if you’re uncomfortable with any of these procedures, don’t hesitate to contact a qualified appliance repair technician for assistance.

Youtube Video:


Quick Wiring Specifications & Terminal Guide

Component / Circuit Standard Wire Gauge Recommended Protection
Control & Trigger Signals 18 – 20 AWG 5A – 7.5A Inline Fuse
Standard Auxiliary Load 14 – 16 AWG 15A – 20A Circuit Breaker
Main Power Feed / Supply 10 – 12 AWG 30A – 40A Heavy-Duty Relay

Images References


Images References, Washing Machine Problems 4

Looking for more diagnostic guides? Explore our complete Washing Machine Problems 4 section for step-by-step troubleshooting solutions.

📚 Related Articles

Scroll to Top