Introduction
Discovering your Maytag washer isn’t draining properly can be a frustrating experience. A washer full of water not only prevents you from doing laundry but can also lead to unpleasant odors and potential water damage if left unattended. This problem often arises mid-cycle or after a completed wash, signaling an issue with the draining system. Addressing this quickly is crucial to prevent further inconvenience and potential damage to your appliance and home.
💡 Technical Key Takeaways:
- Core Focus: Diagnostic schematic and terminal connection layout for Maytag Washer Won T Drain Water.
- Target Scope: Field technicians, automotive DIYers, and residential/commercial electricians.
- Safety Rule: Always disconnect the primary power source/battery terminal and verify zero voltage with a multimeter before touching wires.
Common Causes of Maytag Washer Won’t Drain Water
Several factors can contribute to your Maytag washer’s draining woes:
- Clogged Drain Hose: A kinked, twisted, or blocked drain hose prevents water from escaping the washer.
- Obstructed Drain Pump Filter: Lint, debris, and small objects can accumulate in the drain pump filter, restricting water flow.
- Faulty Drain Pump: A malfunctioning drain pump may be unable to effectively pump water out of the washer.
- Blocked Drainpipe: The drainpipe where your washer empties may be clogged, preventing water from draining.
- Lid Switch Issues: Some washers have a lid switch that must be engaged for the drain cycle to activate. A faulty switch can halt the process.
- Air Lock in Drain Hose: An air pocket within the drain hose can prevent water from siphoning out.
- Control Panel Malfunction: Occasionally, a glitch in the washer’s control panel can disrupt the drain cycle.
- Over sudsing: Too much detergent can cause excessive suds that impede the draining process.
Symptoms Checklist
Use this checklist to pinpoint the problem:
- Washer is full of water after the wash cycle.
- You hear a humming noise, but the water doesn’t drain.
- Water drains very slowly.
- You see error codes related to draining on the control panel.
- The drain hose appears kinked or blocked.
How to Fix Maytag Washer Won’t Drain Water Step-by-Step Guide
- Unplug the Washer: For safety, always disconnect the washer from the power outlet before any troubleshooting.
- Check the Drain Hose for Kinks: Straighten any kinks or bends in the drain hose. Ensure it’s not crushed or pinched.
- Inspect the Drain Hose Connection: Verify that the drain hose is securely connected to both the washer and the drainpipe.
- Check for Blockages in the Drain Hose: Detach the drain hose from the drainpipe. Hold it up and see if water flows freely. If not, try flushing it with a garden hose to dislodge any debris.
- Locate and Clean the Drain Pump Filter: Refer to your washer’s manual to find the drain pump filter. Typically, it’s located at the bottom front or rear of the machine, behind a small access panel.
- Prepare for Water Spillage: Place a shallow pan or towels beneath the drain pump filter access point to catch any water that may spill out.
- Remove the Drain Pump Filter: Carefully unscrew or release the drain pump filter, following the instructions in your manual.
- Clean the Filter: Remove any lint, hair, coins, or other debris from the filter. Rinse it thoroughly under running water.
- Reinstall the Filter: Securely reattach the drain pump filter, ensuring it’s properly sealed.
- Check the Drainpipe: If you suspect a blockage in the drainpipe, carefully use a plumbing snake or auger to clear any obstructions.
- Test the Lid Switch: Manually depress the lid switch (with the washer unplugged!) to see if it moves freely. If it feels loose or damaged, it may need attention.
- Try a Washer Reset: Some washers can be reset by unplugging them for 1-2 minutes, then plugging them back in. This can sometimes clear minor glitches.
- Check for Over Sudsing: If you’ve used too much detergent, run an empty rinse cycle to flush out excess suds. Consider using HE (High Efficiency) detergent, which produces fewer suds.
- Level the Washer: Ensure the washer is level. An unlevel washer can sometimes cause draining issues. Adjust the leveling feet at the bottom of the machine as needed.
- Run a Test Cycle: After performing these checks, run a short wash cycle to see if the washer drains properly.
Fix the Issue Without Buying Parts
Before resorting to replacing parts, try these free methods:
- Reset the Washer: Unplug the washer for a few minutes to reset the electronic controls.
- Cleaning Cycles: Run a washer cleaning cycle with a washer cleaner to remove buildup and debris.
- Regular Maintenance: Regularly clean the drain pump filter and check the drain hose to prevent future issues.
- Inspect the Basket: Check for items trapped in the inner drum of the washing machine.
When Replacement Might Be Necessary
If the above steps don’t resolve the issue, the drain pump itself might be faulty and need replacement. The cost of a drain pump typically ranges from $50 to $150 USD, plus the cost of labor if you hire a technician. Other parts that could potentially fail include the lid switch or the control panel, but these are less common culprits. For more related activities, check out our Kenmore Washer Not Draining Properly.
Safety Warning
- Always unplug the washer before performing any maintenance or repairs.
- Be cautious when handling water near electrical components.
- Clean up any spilled water immediately to prevent slips and falls.
Tools You May Need
- Screwdrivers (Phillips and flathead)
- Pliers
- Bucket or shallow pan
- Towels
- Plumbing snake or auger (for clearing drainpipe clogs)
- Gloves
FAQ
Q: Why is my washer making a humming noise but not draining?
A: This usually indicates a blockage in the drain pump or a faulty drain pump motor. Check the filter and pump for obstructions.
Q: How often should I clean the drain pump filter?
A: Ideally, clean the drain pump filter every 3 months, or more frequently if you wash heavily soiled items.
Q: What if my washer displays an error code related to draining?
A: Consult your washer’s manual to identify the specific error code and its meaning. This can provide valuable clues about the problem.
Q: Can I use a liquid drain cleaner in my washing machine?
A: It’s generally not recommended, as these chemicals can damage the washer’s components. Focus on manual cleaning methods instead.
Conclusion
Dealing with a washer that won’t drain can be a headache, but by following these troubleshooting steps, you can often resolve the issue yourself. Remember to prioritize safety and take your time. If you’ve exhausted all the troubleshooting options and your washer still won’t drain, it might be time to consult a qualified appliance repair technician. However, with a little effort, you might just save yourself a service call and get your laundry routine back on track!
Youtube Video:
Quick Wiring Specifications & Terminal Guide
| Component / Circuit | Standard Wire Gauge | Recommended Protection |
|---|---|---|
| Control & Trigger Signals | 18 – 20 AWG | 5A – 7.5A Inline Fuse |
| Standard Auxiliary Load | 14 – 16 AWG | 15A – 20A Circuit Breaker |
| Main Power Feed / Supply | 10 – 12 AWG | 30A – 40A Heavy-Duty Relay |
Images References
Looking for more diagnostic guides? Explore our complete Washing Machine Problems 4 section for step-by-step troubleshooting solutions.
