Introduction
An LG washing machine that continuously fills with water, even when it’s turned off, is a frustrating and potentially damaging problem. This issue not only wastes water and increases your water bill, but it can also lead to flooding and damage to your home. It often occurs after a wash cycle is complete or even when the machine is completely idle. Addressing this problem promptly is essential to prevent further damage and unnecessary expense.
💡 Technical Key Takeaways:
- Core Focus: Diagnostic schematic and terminal connection layout for Lg Washing Machine Inlet Water Not Stopping.
- Target Scope: Field technicians, automotive DIYers, and residential/commercial electricians.
- Safety Rule: Always disconnect the primary power source/battery terminal and verify zero voltage with a multimeter before touching wires.
Common Causes of lg washing machine inlet water not stopping
Here are some common reasons why your LG washing machine might be experiencing this issue:
- Faulty Inlet Valve: The inlet valve controls the flow of water into the machine. If it’s stuck open or malfunctioning, it can cause continuous filling.
- Water Pressure Issues: Excessively high water pressure can overwhelm the inlet valve and cause it to leak.
- Clogged Inlet Valve Filter: Debris in the water supply can clog the filter screen on the inlet valve, preventing it from closing properly.
- Defective Water Level Sensor: The water level sensor tells the machine when to stop filling. A faulty sensor might not signal the machine to shut off the water.
- Damaged or Kinked Inlet Hose: A damaged or kinked hose can restrict water flow and interfere with the valve’s operation.
- Control Board Malfunction: In rare cases, a problem with the control board can cause it to send incorrect signals to the inlet valve.
- Loose Wiring: Sometimes, loose or corroded wiring connected to the inlet valve can cause it to malfunction.
- Drain Issues: A clogged drain can prevent the water from draining out properly, making it appear that the water is constantly filling.
Symptoms Checklist
Check for these signs to confirm the issue:
- Water continuously trickling or flowing into the washing machine drum.
- Water filling the drum even when the machine is turned off.
- A hissing sound coming from the water inlet area when the machine is off.
- The water level rising above the normal fill line.
- The washing machine overflowing.
How to Fix lg washing machine inlet water not stopping Step-by-Step Guide
Follow these steps to troubleshoot and fix the problem:
- Turn Off the Water Supply: Locate the cold and hot water shut-off valves behind your washing machine and turn them off completely.
- Unplug the Washing Machine: For safety, unplug the washing machine from the electrical outlet.
- Inspect the Inlet Hoses: Check the inlet hoses for any kinks, bends, or damage. Straighten any kinks and replace damaged hoses.
- Clean the Inlet Valve Filters: Disconnect the inlet hoses from the back of the washing machine. Inside the hose connection points, you’ll find small mesh filters. Use pliers to carefully remove them and clean them thoroughly with a brush and water. Reinstall the filters.
- Check Water Pressure: If you suspect high water pressure, consider installing a water pressure regulator on your main water line.
- Inspect the Inlet Valve: Visually inspect the inlet valve for any signs of damage or corrosion. You might need to remove the top or back panel of the washing machine to access it. Refer to your owner’s manual for instructions.
- Test the Inlet Valve (Advanced): With the machine unplugged, carefully use a multimeter to check the continuity of the inlet valve solenoid. If there’s no continuity, the valve might be faulty. (Only proceed if you are comfortable with electrical testing).
- Check the Water Level Sensor: The water level sensor is usually located inside the washing machine tub. Inspect it for any damage or debris.
- Look for Loose Wiring: Check all the wiring connections to the inlet valve and water level sensor. Make sure they are secure and free of corrosion.
- Reset the Washing Machine: Some washing machines have a reset function. Consult your owner’s manual for instructions on how to reset your specific model.
- Check the Drain Hose: Ensure the drain hose is properly connected and not clogged. A clogged drain can back up water into the machine.
- Run a Calibration Cycle: Some LG washing machines have a calibration cycle that can help reset the water level settings. Check your owner’s manual for instructions.
- Test a Wash Cycle: After performing these steps, turn the water supply back on, plug in the washing machine, and run a test wash cycle to see if the problem is resolved.
Fix the Issue Without Buying Parts
Before considering replacing any parts, try these free methods:
- Power Cycle: Unplug the washing machine for at least 15 minutes to reset the control board.
- Filter Cleaning: Regularly clean the inlet valve filters to prevent clogs.
- Hose Inspection: Routinely inspect inlet and drain hoses for kinks or damage.
- Calibration: Run the calibration cycle as recommended in your owner’s manual.
When Replacement Might Be Necessary
If the above steps don’t resolve the issue, you might need to replace a part. The inlet valve is a common culprit. Replacement costs range from $30 to $100 USD, depending on the model. The water level sensor can also fail and may cost between $20 and $70 USD to replace. Consider contacting a qualified appliance repair technician for diagnosis and replacement. For more related activities, check out our My Samsung Washing Machine Is Leaking From Underneath.
Safety Warning
- Always unplug the washing machine before performing any repairs.
- Turn off the water supply to prevent flooding.
- Be careful when handling electrical components.
- If you are not comfortable with electrical repairs, contact a qualified technician.
- Clean up any water spills immediately to prevent slips and falls.
Tools You May Need
- Pliers
- Screwdrivers (Phillips and flathead)
- Adjustable wrench
- Bucket
- Old towels
- Multimeter (optional)
FAQ
- Q: Why is my washing machine filling with water even when it’s off? A: This is usually caused by a faulty inlet valve or water level sensor.
- Q: How do I clean the inlet valve filters? A: Disconnect the inlet hoses from the back of the washing machine and remove the small mesh filters inside the hose connections. Clean them with a brush and water.
- Q: How much does it cost to replace the inlet valve? A: The cost ranges from $30 to $100 USD, depending on the model.
- Q: What should I do if I’m not comfortable performing the repairs myself? A: Contact a qualified appliance repair technician for assistance.
Conclusion
Troubleshooting an LG washing machine that won’t stop filling with water can seem daunting, but by following these steps, you can often identify and resolve the issue yourself. Remember to prioritize safety and start with the simplest solutions first. If you’ve exhausted these troubleshooting steps and the problem persists, don’t hesitate to call a qualified appliance repair technician for professional assistance.
Youtube Video:
Quick Wiring Specifications & Terminal Guide
| Component / Circuit | Standard Wire Gauge | Recommended Protection |
|---|---|---|
| Control & Trigger Signals | 18 – 20 AWG | 5A – 7.5A Inline Fuse |
| Standard Auxiliary Load | 14 – 16 AWG | 15A – 20A Circuit Breaker |
| Main Power Feed / Supply | 10 – 12 AWG | 30A – 40A Heavy-Duty Relay |
Images References
Looking for more diagnostic guides? Explore our complete Washing Machine Problems 4 section for step-by-step troubleshooting solutions.
