Kenmore He2 Plus Washer Won T Drain

Introduction

Is your Kenmore HE2 Plus washer refusing to drain? This is a common problem that can leave you with a tub full of water and a pile of wet laundry. It’s not only inconvenient but can also lead to mold and mildew growth if left unresolved. Addressing this issue promptly is crucial to prevent further damage to your washer and to get your laundry routine back on track. Don’t worry; this guide will walk you through the most common causes and how to fix them, step by step.

Common Causes of kenmore he2 plus washer won t drain

Several factors can cause your Kenmore HE2 Plus washer to stop draining. Here are some of the most common:. For more related activities, check out our Hoover Dynamic Next Leaking From Bottom.

• Clogged Drain Hose: A kinked, bent, or blocked drain hose restricts water flow.
• Clogged Drain Pump Filter: Small objects like lint, hair, or socks can block the drain pump filter.
• Faulty Drain Pump: The drain pump might be malfunctioning, preventing it from pumping water out.
• Blocked Drainpipe: The drainpipe where the washer empties could be clogged.
• Air Lock in the Drain Hose: An air bubble can create a vacuum, preventing water from flowing.
• Control Board Issues: A rare but possible cause is a problem with the washer’s control board, which might not be sending the signal to activate the drain pump.
• Too Much Soap: Excessive suds can overwhelm the pump’s ability to drain properly.
• Kinked or Damaged Belt: If your pump is belt-driven, a damaged or loose belt might prevent it from working.

Symptoms Checklist

Use this checklist to accurately identify the issue:

• Washer completes the wash cycle but the tub remains full of water.
• You hear a humming or buzzing sound from the washer, but the water doesn’t drain.
• The washer displays an error code related to draining.
• The drain hose appears to be kinked or blocked.
• The drain pump filter is visibly clogged.
• Water drains very slowly or not at all.

How to Fix kenmore he2 plus washer won t drain Step-by-Step Guide

Follow these steps to troubleshoot and fix your Kenmore HE2 Plus washer:

1. Unplug the Washer: For safety, always disconnect the power before working on your appliance.
2. Check the Drain Hose for Kinks: Inspect the entire length of the drain hose for any kinks, bends, or crushing that might be blocking the water flow. Straighten any kinks you find.
3. Detach the Drain Hose: Carefully detach the drain hose from the back of the washer and from the drainpipe.
4. Flush the Drain Hose: Use a garden hose or faucet to flush the drain hose with water, dislodging any debris. If it’s badly clogged, you may need to use a plumbing snake.
5. Check the Drainpipe: Make sure the drainpipe where the washer empties is clear. You can use a plumbing snake to clear any blockages.
6. Locate the Drain Pump Filter: The drain pump filter is usually located at the bottom front of the washer, behind a small access panel. Consult your owner’s manual for the exact location.
7. Drain Remaining Water: Place a shallow pan or towels beneath the access panel to catch any water that spills out when you remove the filter.
8. Remove and Clean the Drain Pump Filter: Carefully unscrew or pull out the drain pump filter. Clean it thoroughly, removing any lint, hair, coins, or other debris.
9. Inspect the Drain Pump: While the filter is removed, shine a flashlight into the drain pump housing. Check for any obstructions that might be preventing the pump from working.
10. Reassemble the Drain Pump Filter: Reinstall the cleaned drain pump filter, making sure it’s securely in place.
11. Reconnect the Drain Hose: Reattach the drain hose to the back of the washer and to the drainpipe. Ensure that the connections are tight.
12. Check for Air Lock: Make sure the drain hose isn’t pushed too far down into the drain pipe. This can create a siphon effect. Ideally, there should be an air gap.
13. Run a Test Cycle: Plug the washer back in and run a short drain/spin cycle to see if the issue is resolved.
14. Reduce Soap Usage: If excess suds are a potential problem, try using less detergent in future loads.

Fix the Issue Without Buying Parts

Before considering replacement parts, try these free methods:

• Reset the Washer: Unplug the washer for 5-10 minutes to reset the electronic controls.
• Cleaning Cycle: Run a cleaning cycle with a washer cleaner to remove buildup that can affect draining.
• Regular Maintenance: Clean the drain pump filter regularly to prevent clogs.
• Inspect Hoses Periodically: Check the drain hose for kinks or damage during routine laundry maintenance.

When Replacement Might Be Necessary

If you’ve tried all the troubleshooting steps and your washer still won’t drain, the drain pump itself might be faulty and need replacement. A new drain pump can cost between $50 and $150 USD. In rare cases, the control board might be the issue, which is a more expensive repair. A control board can cost between $150 and $300 USD. The drain pump is the most commonly failing part related to drainage issues.

Safety Warning

• Always unplug the washer before attempting any repairs.
• Be careful when handling water, as it can create a slip hazard. Clean up any spills immediately.
• If you’re not comfortable working with electrical appliances, consult a qualified technician.

Tools You May Need

• Screwdriver (Phillips and flathead)
• Pliers
• Shallow pan or towels
• Flashlight
• Plumbing snake (optional)

FAQ

Here are some frequently asked questions about washer draining issues:

• Q: Why is my washer making a loud noise when it tries to drain?

  A: This could be due to a foreign object stuck in the drain pump or a failing pump motor.

• Q: How often should I clean the drain pump filter?

  A: It’s recommended to clean the drain pump filter every 2-3 months, or more frequently if you wash a lot of lint-producing items.

• Q: Can I use a liquid drain cleaner to unclog my washer?

  A: It’s generally not recommended to use liquid drain cleaners in your washer, as they can damage the pump and other components.

• Q: The “drain/spin” cycle does nothing. Is the motor dead?

  A: Not necessarily. Test the drain pump as described above, especially for blockage. A multimeter can test voltage. A technician is better equipped to test motors.

Conclusion

Don’t let a Kenmore HE2 Plus washer that won’t drain ruin your day. By following these troubleshooting steps, you can often resolve the issue yourself and save the cost of a service call. Remember to prioritize safety and take your time. If you’re still having trouble after trying these solutions, it might be time to call a qualified appliance repair technician.

Youtube Video: