Introduction
A refrigerator that isn’t cooling is a homeowner’s nightmare. Food spoils, money is wasted, and the inconvenience is immense. If your Kenmore 795 refrigerator isn’t keeping things cold like it should, it’s important to address the issue quickly to prevent food spoilage and further damage to your appliance. This guide provides simple, step-by-step instructions to help you diagnose and potentially fix the problem yourself before calling a professional.
💡 Technical Key Takeaways:
- Core Focus: Diagnostic schematic and terminal connection layout for Kenmore 795 Refrigerator Not Cooling.
- Target Scope: Field technicians, automotive DIYers, and residential/commercial electricians.
- Safety Rule: Always disconnect the primary power source/battery terminal and verify zero voltage with a multimeter before touching wires.
Common Causes of kenmore 795 refrigerator not cooling
There are several reasons why your Kenmore 795 refrigerator might not be cooling effectively:
- Dirty Condenser Coils: These coils release heat. If they’re covered in dust, they can’t do their job properly.
- Blocked Air Vents: Items inside the refrigerator can block the vents that circulate cold air between the freezer and refrigerator compartments.
- Faulty Door Seals: Damaged or dirty door seals allow warm air to enter, forcing the refrigerator to work harder.
- Overloaded Refrigerator: Packing too much food inside restricts airflow and reduces cooling efficiency.
- Incorrect Temperature Settings: Make sure the thermostat is set to the correct temperature for both the refrigerator and freezer.
- Frost Buildup in Freezer: Excessive frost can insulate the evaporator coils, preventing them from cooling effectively.
- Failed Start Relay: The start relay helps the compressor start. If it fails, the compressor won’t run.
- Damaged Condenser Fan Motor: The condenser fan helps cool the condenser coils. If it’s not working, the coils can overheat.
- Evaporator Fan Motor malfunction The fan may be blocked with ice buildup due to defrost system issues
Symptoms Checklist
Check if any of these symptoms apply to your situation:
- Refrigerator feels warm to the touch inside.
- Food is spoiling faster than usual.
- The compressor (usually located at the back of the refrigerator) is not running.
- The refrigerator is making unusual noises.
- Freezer is working fine, but the refrigerator is warm.
- Freezer is not cold enough, and the refrigerator is warm.
- Excessive frost buildup in the freezer.
How to Fix kenmore 795 refrigerator not cooling Step-by-Step Guide
Follow these steps to troubleshoot your Kenmore 795 refrigerator:
- Check the Power Cord: Make sure the refrigerator is plugged in securely and the outlet is working. Test the outlet with another appliance.
- Inspect Temperature Settings: Verify that the temperature controls are set correctly. Recommended settings are typically around 37F (3C) for the refrigerator and 0F (-18C) for the freezer.
- Clean Condenser Coils: Unplug the refrigerator and locate the condenser coils at the back or bottom. Use a vacuum cleaner with a brush attachment to remove dust and debris.
- Check Air Vents: Make sure air vents inside the refrigerator and freezer are not blocked by food items. Rearrange items to allow for proper airflow.
- Inspect Door Seals: Examine the door seals for any signs of damage, cracks, or dirt. Clean the seals with a damp cloth and mild detergent. If the seals are damaged, they might need to be replaced.
- Defrost the Refrigerator: If there’s excessive frost buildup in the freezer, manually defrost the refrigerator. Unplug the appliance and leave the doors open for several hours, allowing the frost to melt. Place towels to absorb water.
- Check the Condenser Fan: Locate the condenser fan (usually near the compressor). Make sure it’s free from obstructions and spinning correctly. If it’s not spinning, it might be faulty.
- Check the Evaporator Fan: The evaporator fan is located inside the freezer. Open the freezer door and manually rotate the fan. If it does not spin freely, it could be obstructed by ice or a failed motor.
- Listen to the Compressor: Listen to see if the compressor is running. It should emit a low humming sound. If it’s silent, the compressor might be failing.
- Check the Start Relay:(advanced users only) Located on the side of the compressor is the start relay, it has a set of wires that connects to the compressor. To test this part you must use a multimeter to see if it is working.
- Reset the Refrigerator: Unplug the refrigerator for 5-10 minutes, then plug it back in. This can sometimes reset the system and resolve minor issues.
- Ensure Proper Ventilation: Make sure the refrigerator has adequate space around it for proper ventilation (at least a few inches on all sides).
- Avoid Overpacking: Make sure your refrigerator is not overloaded with food. Overpacking can restrict airflow.
- Level the Refrigerator: Make sure the refrigerator is level. An unlevel refrigerator can cause door seal issues and affect cooling performance.
Fix the Issue Without Buying Parts
Sometimes, you can fix the issue without replacing any parts:
- Reset: Unplugging the refrigerator for 5-10 minutes can reset the system.
- Cleaning: Regularly cleaning the condenser coils and door seals is essential for maintaining optimal performance.
- Recalibration: Some refrigerators have a self-diagnostic mode that can recalibrate the temperature sensors. Refer to your owner’s manual for instructions.
- Inspection Tips: Regularly inspect the refrigerator for any signs of damage or wear and tear.
- Maintenance Basics: Proper ventilation, avoiding overpacking, and leveling the refrigerator are essential maintenance practices.
When Replacement Might Be Necessary
If you’ve tried all the troubleshooting steps and your refrigerator still isn’t cooling, a component might have failed. Common parts that might need replacement include:
- Compressor: This is the most expensive component to replace (estimated cost: $300-$800 plus labor).
- Condenser Fan Motor: This motor helps cool the condenser coils (estimated cost: $50-$150 plus labor).
- Evaporator Fan Motor: This motor circulates air inside the freezer (estimated cost: $50-$150 plus labor).
- Start Relay: Helps start the compressor (estimated cost: $20 – $50 plus labor).
If you suspect a major component has failed, it’s often best to consult with a qualified appliance repair technician.
Safety Warning
- Always unplug the refrigerator before performing any maintenance or repairs.
- Avoid working on electrical components if you’re not comfortable or experienced.
- Keep the floor around the refrigerator dry to prevent electric shock.
- Be careful when handling tools and components to avoid injury.
- If you are not comfortable with this repair, contact a professional technician.
Tools You May Need
- Screwdrivers (Phillips and flathead)
- Vacuum cleaner with a brush attachment
- Damp cloth and mild detergent
- Multimeter (for testing electrical components – advanced users only)
- Gloves
FAQ
Here are some frequently asked questions about Kenmore 795 refrigerator cooling problems:
- Q: Why is my freezer cold but my refrigerator is warm? A: This is often caused by blocked air vents between the freezer and refrigerator compartments.
- Q: How often should I clean the condenser coils? A: It’s recommended to clean the condenser coils every 6-12 months.
- Q: What temperature should I set my refrigerator and freezer to? A: The recommended settings are 37F (3C) for the refrigerator and 0F (-18C) for the freezer.
- Q: My refrigerator is making a clicking noise but not cooling. What could be the problem? A: This could indicate a problem with the compressor or the start relay.
- Q: I have a large block of ice building up in my freezer even with it set to a low temp. What do I do? A: This can indicate a malfunction of the defrost system and you may need a technician.
Conclusion
Troubleshooting a Kenmore 795 refrigerator that’s not cooling can seem daunting, but by following these steps, you can often diagnose and fix the problem yourself. Remember to prioritize safety and always unplug the appliance before performing any maintenance. If you’ve exhausted these troubleshooting steps and your refrigerator still isn’t cooling, it might be time to consult with a qualified appliance repair technician. Good luck!
Youtube Video:
Quick Wiring Specifications & Terminal Guide
| Component / Circuit | Standard Wire Gauge | Recommended Protection |
|---|---|---|
| Control & Trigger Signals | 18 – 20 AWG | 5A – 7.5A Inline Fuse |
| Standard Auxiliary Load | 14 – 16 AWG | 15A – 20A Circuit Breaker |
| Main Power Feed / Supply | 10 – 12 AWG | 30A – 40A Heavy-Duty Relay |
Images References
Looking for more diagnostic guides? Explore our complete Refrigerator Problems 1 section for step-by-step troubleshooting solutions.
