Introduction
Discovering your Amana washing machine fills with water only to immediately drain it away can be incredibly frustrating. This means your clothes aren’t being washed properly, and you’re wasting water and energy. It usually happens during the wash cycle or even right after the fill cycle completes. Addressing this issue promptly is crucial to prevent further water wastage and potential damage to your laundry room. Don’t worry, often the problem is simple to diagnose and fix!
💡 Technical Key Takeaways:
- Core Focus: Diagnostic schematic and terminal connection layout for Amana Washer Fills Then Drains.
- Target Scope: Field technicians, automotive DIYers, and residential/commercial electricians.
- Safety Rule: Always disconnect the primary power source/battery terminal and verify zero voltage with a multimeter before touching wires.
Common Causes of Amana Washer Fills Then Drains
Here are some common reasons why your Amana washer might be filling and then draining:
- Drain Hose Issues: The drain hose could be inserted too far down the drainpipe, creating a siphoning effect.
- Clogged Drain Hose: A blockage in the drain hose can prevent proper drainage, leading to continuous draining during the fill cycle.
- Faulty Drain Valve: The drain valve might be stuck open, causing water to drain as soon as it enters the machine.
- Siphon Effect from Drainpipe: The drainpipe might be too low, creating a siphon that pulls water out of the washer.
- Tilted Washing Machine: If your washing machine isn’t level, it can trigger the drain pump prematurely.
- Pressure Switch Malfunction: A faulty pressure switch might be incorrectly signaling that the washer is full, causing it to drain.
- Belt slippage (for belt-driven washers): A worn or loose belt can cause inconsistent motor performance, affecting the draining process.
- Control Board Problems: Though less common, a malfunctioning control board can send incorrect signals to the drain pump.
Symptoms Checklist
Confirm if you are experiencing the “fills then drains” issue by checking for these:
- Water immediately starts draining as the washer fills.
- The washer fails to agitate or tumble clothes.
- You can hear the drain pump running constantly.
- Error codes related to draining or water level appear on the display (if your model has one).
- The washer stops mid-cycle with water drained.
How to Fix Amana Washer Fills Then Drains Step-by-Step Guide
- Unplug the Washer: Always disconnect the power cord before starting any troubleshooting.
- Check the Drain Hose Insertion: Make sure the drain hose is not pushed too far into the drainpipe. Aim for about 6-8 inches of insertion.
- Inspect the Drain Hose for Kinks or Blockages: Remove the drain hose and examine it for kinks, bends, or visible clogs. Straighten out any kinks.
- Flush the Drain Hose: Disconnect the drain hose and run water through it to dislodge any debris.
- Inspect the Drainpipe: Ensure the drainpipe is not clogged. You can use a drain snake to clear any obstructions.
- Check Washer Level: Use a level to ensure the washing machine is properly balanced. Adjust the leveling feet as needed.
- Clean the Drain Pump Filter (if accessible): Some models have a cleanable filter near the drain pump. Consult your owner’s manual for its location and cleaning instructions.
- Inspect the Drain Valve (Difficult): This is a more advanced step. Locate the drain valve (usually at the bottom of the machine). Check if it is stuck open. You might need to remove panels to access it. Be careful and refer to repair videos if needed.
- Check the Air Dome (if present): On some older models, there is an air dome connected to the pressure switch. Make sure it is clear of obstructions.
- Try a Washer Reset: Unplug the washer for 1-2 minutes, then plug it back in. This can sometimes reset the control board.
- Run a Calibration Cycle (if applicable): Some Amana washers have a calibration cycle to reset the water level sensor. Check your owner’s manual for instructions.
Fix the Issue Without Buying Parts
Before considering replacing any parts, try these free and simple solutions:
- Resetting the Washer: As mentioned, unplugging the washer for a few minutes can often resolve minor electronic glitches.
- Cleaning the Drain Hose and Drainpipe: Regular cleaning can prevent blockages that cause draining issues.
- Ensuring the Washer is Level: A properly leveled washer operates more efficiently and reduces the risk of premature draining.
- Routine Maintenance: Perform regular cleaning cycles with a washing machine cleaner to prevent buildup and maintain optimal performance.
- Look for error codes: Many washing machines have an error code display that provides a starting place for your troubleshooting. Consult your user manual.
When Replacement Might Be Necessary
If you’ve tried all the troubleshooting steps and the issue persists, a part may need replacement. Common parts that fail include the drain valve ($30-$70), the pressure switch ($20-$50), or the control board ($100-$300). If you’re not comfortable replacing these yourself, a technician visit typically costs between $100 and $250, plus the cost of parts.
Safety Warning
- Always unplug the washing machine before performing any troubleshooting or repairs.
- Be cautious when working with water and electricity to avoid electric shock.
- Clean up any spills immediately to prevent slips and falls.
- If you are not comfortable with electrical or mechanical repairs, consult a qualified appliance technician.
Tools You May Need
- Screwdrivers (Phillips and flathead)
- Pliers
- Adjustable wrench
- Level
- Bucket
- Drain snake (optional)
FAQ
Q: Why is my washer draining when it’s supposed to be filling?
A: The most likely causes are a drain hose inserted too far into the drainpipe, a clogged drain hose, or a faulty drain valve.
Q: How do I know if my drain hose is the problem?
A: Disconnect the drain hose and inspect it for kinks, bends, or visible clogs. Flush it with water to remove any debris.
Q: Can a tilted washer cause draining problems?
A: Yes, if your washing machine isn’t level, it can trigger the drain pump prematurely.
Q: What if I’ve tried everything, and it still drains while filling?
A: It’s likely a faulty drain valve, pressure switch, or a more serious control board issue that may require professional repair.
Conclusion
Troubleshooting an Amana washer that fills then drains can seem daunting, but by following these steps, you can often identify and resolve the issue yourself. Start with the simplest solutions, and work your way through the more complex ones. Remember to prioritize safety and consult a qualified technician if you’re uncomfortable with any of the repairs. You may be able to save yourself a repair bill and get your washing machine running smoothly again!
Youtube Video:
Quick Wiring Specifications & Terminal Guide
| Component / Circuit | Standard Wire Gauge | Recommended Protection |
|---|---|---|
| Control & Trigger Signals | 18 – 20 AWG | 5A – 7.5A Inline Fuse |
| Standard Auxiliary Load | 14 – 16 AWG | 15A – 20A Circuit Breaker |
| Main Power Feed / Supply | 10 – 12 AWG | 30A – 40A Heavy-Duty Relay |
Images References
Looking for more diagnostic guides? Explore our complete Washing Machine Problems 2 section for step-by-step troubleshooting solutions.
