Introduction
Is your Whirlpool washer constantly draining, even when it’s not supposed to? This frustrating issue means your clothes aren’t getting properly washed, your water bill is going up, and your washer is essentially useless. It often happens mid-cycle or even when the washer is turned off. Addressing this quickly prevents potential water damage to your home and further wear and tear on your appliance.
💡 Technical Key Takeaways:
- Core Focus: Diagnostic schematic and terminal connection layout for Whirlpool Washer Won T Stop Draining.
- Target Scope: Field technicians, automotive DIYers, and residential/commercial electricians.
- Safety Rule: Always disconnect the primary power source/battery terminal and verify zero voltage with a multimeter before touching wires.
Common Causes of Whirlpool Washer Won’t Stop Draining
Several things can cause your Whirlpool washer to keep draining. Here are some of the most common culprits:. For more related activities, check out our Washing Machine Leaking From Draw.
- Clogged Drain Hose: Debris like lint, socks, or other small items can block the drain hose, causing a siphon effect.
- Faulty Drain Valve: The drain valve controls when water is released. If it’s stuck open, water will continuously drain.
- Siphoning Issue: If the drain hose is inserted too far into the drainpipe, it can create a siphon, pulling water out.
- Defective Water Inlet Valve: Although rare, a leaking water inlet valve can continuously fill the tub, which the washer then tries to drain.
- Control Board Malfunction: The control board dictates all the washer’s functions. A glitch can cause it to mistakenly signal the drain pump to run constantly.
- Drain Pump Problem: A faulty drain pump may continuously run, even when not needed.
- Incorrect Drain Hose Height: If the drain hose is too low, gravity can cause it to drain continuously.
- Air Admittance Valve Issue: Your plumbing system might have a clogged or malfunctioning air admittance valve which can cause siphoning through the washer.
Symptoms Checklist
Use this checklist to confirm the problem:
- The washer drains even when turned off.
- The washer drains constantly during a cycle.
- The washer drains before the spin cycle starts.
- You hear the drain pump running continuously.
- Water trickles out of the drain hose even when the washer is off.
- The wash tub never fills completely.
How to Fix Whirlpool Washer Won’t Stop Draining Step-by-Step Guide
Follow these steps to troubleshoot and fix your continuously draining Whirlpool washer:
- Unplug the Washer: Always start by unplugging the washer from the power outlet to ensure your safety.
- Inspect the Drain Hose: Detach the drain hose from the drainpipe. Look for kinks, clogs, or obstructions. Straighten any kinks and remove any visible debris.
- Check for Siphoning: Ensure the drain hose isn’t inserted too far into the drainpipe. A good rule of thumb is to insert it no more than 6 inches.
- Verify Drain Hose Height: The top of the drain hose should be at least 30 inches above the floor to prevent siphoning.
- Clean the Drain Hose: Use a garden hose or a long, flexible brush to flush out any hidden debris in the drain hose.
- Access the Drain Pump: Locate the drain pump. This is usually accessible from the front or back panel of the washer. Consult your washer’s manual for specific instructions.
- Check the Drain Pump Filter: Many Whirlpool washers have a drain pump filter to catch debris. Carefully remove the filter (be prepared for some water to spill) and clean it thoroughly.
- Inspect the Drain Pump: Visually inspect the drain pump for any signs of damage or blockage. Gently try to turn the pump impeller (fan blades) by hand. It should move freely.
- Check the Drain Valve: The drain valve is often integrated with the drain pump. Look for any signs of damage or debris that might be preventing it from closing properly.
- Check Water Inlet Valve: Turn off both hot and cold water supply to the washer, and observe the water level in the washer. If water level keeps increasing, there is a chance that water inlet valve is defected and needs replacement.
- Run a Calibration Cycle (If Available): Some Whirlpool models have a calibration cycle that can reset the control board and resolve minor glitches. Consult your owner’s manual for instructions.
- Check the Air Admittance Valve: Locate the air admittance valve for your plumbing system. This valve is often located under a sink or behind a washing machine. Remove the top cover, check for debris, and consider replacing if in doubt.
- Plug the Washer Back In: Once you’ve completed these checks, plug the washer back in.
- Run a Test Cycle: Select a short wash cycle and observe if the washer still drains continuously.
Fix the Issue Without Buying Parts
Before considering part replacements, try these free methods:
- Reset the Washer: Unplug the washer for 5 minutes, then plug it back in. This can sometimes reset the control board.
- Clean the Washer: Run a washer cleaner cycle with a commercial washing machine cleaner to remove buildup and debris.
- Recalibrate the Washer: Consult your owner’s manual for specific recalibration instructions for your model.
- Regular Maintenance: Clean the lint filter regularly, use the correct amount of detergent, and avoid overloading the washer to prevent future issues.
When Replacement Might Be Necessary
If you’ve tried all the troubleshooting steps and your washer still won’t stop draining, a part replacement may be necessary. Common parts that fail include the drain pump ($50-$150), the drain valve ($30-$80), or, in rare cases, the control board ($100-$300). Consider consulting a qualified appliance repair technician to diagnose the problem accurately before replacing any parts.
Safety Warning
- Always unplug the washer before performing any maintenance or repairs.
- Turn off the water supply to the washer before disconnecting any water lines.
- Be careful when handling water, as wet floors can be slippery.
- If you’re uncomfortable with any of these steps, contact a qualified appliance repair technician.
Tools You May Need
- Screwdrivers (Phillips and flathead)
- Pliers
- Bucket
- Towels
- Flashlight
- Garden hose or flexible brush
FAQ
Here are some frequently asked questions about washing machines that continuously drain:
- Q: Why is my washer draining even when it’s turned off? A: This is often due to a siphoning issue, a faulty drain valve, or a leaking water inlet valve.
- Q: How do I know if my drain pump is bad? A: If the drain pump is making unusual noises, not draining the water efficiently, or running constantly, it may be failing.
- Q: Can I fix a washing machine myself? A: Many common washing machine problems can be fixed with basic troubleshooting and simple repairs.
- Q: How often should I clean my washing machine? A: It’s recommended to clean your washing machine monthly to prevent buildup and odors.
- Q: How do I reset my Whirlpool washer? A: Unplug the washer for 5 minutes, then plug it back in. This can sometimes reset the control board.
Conclusion
A Whirlpool washer that won’t stop draining can be a real headache, but with a little patience and this guide, you can often diagnose and fix the problem yourself. Try the troubleshooting steps before calling a technician, you may save time and money. However, don’t hesitate to seek professional help if you’re uncomfortable with any of the repairs.
Quick Wiring Specifications & Terminal Guide
| Component / Circuit | Standard Wire Gauge | Recommended Protection |
|---|---|---|
| Control & Trigger Signals | 18 – 20 AWG | 5A – 7.5A Inline Fuse |
| Standard Auxiliary Load | 14 – 16 AWG | 15A – 20A Circuit Breaker |
| Main Power Feed / Supply | 10 – 12 AWG | 30A – 40A Heavy-Duty Relay |
Images References
Looking for more diagnostic guides? Explore our complete Washing Machine Problems 6 section for step-by-step troubleshooting solutions.
