Washing Machine Will Spin But Not Drain


Washing Machine Will Spin But Not Drain

Introduction

Is your washing machine spinning clothes dry but leaving a pool of water at the bottom after the cycle finishes? This frustrating issue, where your washing machine will spin but not drain, is a common problem for homeowners. It means the water isn’t being properly expelled, leading to wet clothes and a machine that’s out of commission. Addressing this quickly is important to prevent mold growth, musty smells, and potential damage to your laundry room. Let’s get your washing machine back in working order!

💡 Technical Key Takeaways:

  • Core Focus: Diagnostic schematic and terminal connection layout for Washing Machine Will Spin But Not Drain.
  • Target Scope: Field technicians, automotive DIYers, and residential/commercial electricians.
  • Safety Rule: Always disconnect the primary power source/battery terminal and verify zero voltage with a multimeter before touching wires.

Common Causes of Washing Machine Will Spin But Not Drain

Here are some typical reasons why your washing machine might spin but not drain:

  • Clogged Drain Hose: This is often the culprit. Lint, small items, or debris can block the hose that carries water away.
  • Blocked Drain Pump Filter: Many washing machines have a filter to catch debris before it reaches the pump. This filter can become clogged.
  • Kinked or Damaged Drain Hose: A bend or crack in the hose can restrict water flow.
  • Faulty Drain Pump: The pump itself might be malfunctioning and unable to push the water out.
  • Clogged Drainpipe: The house drain that the washing machine connects to might be clogged.
  • Air Lock in Drain Hose: Sometimes air can get trapped, preventing proper drainage.
  • Lid Switch Problem: Some machines won’t drain if the lid switch is faulty, as it prevents the spin cycle from fully engaging to expel water.
  • Control Board Issues: In rare cases, a problem with the washing machine’s electronic control board could prevent the drain cycle from starting.

Symptoms Checklist

Here’s how to accurately identify that your washing machine is spinning but not draining:

  • Clothes are wet after the spin cycle.
  • Water remains in the washing machine drum after the cycle.
  • You may hear the washing machine spinning, but no water is being pumped out.
  • You might notice a gurgling sound during the drain cycle.
  • Error codes related to draining issues may appear on the machine’s display panel.

How to Fix Washing Machine Will Spin But Not Drain Step-by-Step Guide

Follow these steps to troubleshoot the drainage issue:

  1. Unplug the Washing Machine: Safety first! Disconnect the washing machine from the power outlet.
  2. Locate the Drain Hose: This is usually a flexible hose at the back of the machine, connected to a drainpipe or utility sink.
  3. Check for Kinks or Damage: Inspect the hose for any bends, crimps, or cracks. Straighten out any kinks and replace the hose if damaged.
  4. Disconnect the Drain Hose: Carefully detach the hose from both the washing machine and the drainpipe. Have a bucket ready to catch any remaining water.
  5. Flush the Drain Hose: Use a garden hose or faucet to flush water through the drain hose to dislodge any clogs.
  6. Locate the Drain Pump Filter: This is usually located at the front bottom of the machine, behind a small access panel. Consult your owner’s manual for the exact location.
  7. Drain the Filter Housing: Place a shallow pan or towel under the access panel. Open the panel and carefully unscrew the filter cap. Some water will drain out.
  8. Clean the Drain Pump Filter: Remove the filter and clean it thoroughly, removing any lint, hair, coins, or other debris.
  9. Inspect the Drain Pump Impeller: With the filter removed, reach inside the pump housing and check if the impeller (a small fan-like component) can spin freely. Remove any obstructions.
  10. Check the Drainpipe: Ensure the house drainpipe is not clogged. You can use a drain snake to clear any blockages.
  11. Reconnect the Drain Hose: Reattach the drain hose securely to both the washing machine and the drainpipe.
  12. Reinstall the Drain Pump Filter: Screw the filter cap back into place, making sure it’s tight. Close the access panel.
  13. Plug in the Washing Machine: Reconnect the washing machine to the power outlet.
  14. Run a Test Cycle: Select a short wash and drain cycle to see if the problem is resolved. Observe if the water drains properly.
  15. Check the Lid Switch: If all else fails, sometimes the machine wont drain due to the lid switch. Check if the lid switch is working by carefully opening and closing the lid to see if it activates properly.

Fix the Issue Without Buying Parts

Here are some ways to resolve the draining issue without immediately resorting to part replacement:

  • Reset the Washing Machine: Unplug the machine for a few minutes and then plug it back in. This can sometimes reset the electronic controls.
  • Clean the Entire Machine: Run an empty wash cycle with a washing machine cleaner to remove buildup and potential clogs.
  • Inspect the Air Gap: If your installation includes an air gap, clear this.
  • Recalibrate Machine: Look in your user manual on how to recalibrate the washer.

When Replacement Might Be Necessary

If the above steps don’t solve the problem, the drain pump might be faulty and need replacing. A new drain pump typically costs between $50 and $150 USD, plus labor if you hire a technician. Other parts that could potentially fail are the drain hose itself (around $20-$50) or, in rare cases, the control board (potentially $100-$300+). For more related activities, check out our Whirlpool Washer Loud Noise During Spin Cycle.

Safety Warning

  • Always unplug the washing machine before performing any repairs.
  • Be careful when handling water and electrical components.
  • Avoid standing in water while working with the machine.
  • If you’re uncomfortable with electrical or plumbing repairs, consult a qualified technician.

Tools You May Need

  • Screwdrivers (Phillips and flathead)
  • Pliers
  • Bucket or shallow pan
  • Towels
  • Garden hose
  • Drain snake

FAQ

Here are some frequently asked questions about washing machine draining problems:

  • Q: Why is my washing machine spinning but not draining after a power outage? A: A power outage can sometimes disrupt the washing machine’s cycle. Try resetting the machine by unplugging it for a few minutes.
  • Q: How often should I clean the drain pump filter? A: It’s recommended to clean the filter every 1-3 months, depending on how frequently you use the washing machine.
  • Q: Can I use a chemical drain cleaner in my washing machine? A: It’s generally not recommended, as harsh chemicals can damage the machine’s components.
  • Q: What does the UE code mean on my LG washer? A: The UE code is unbalanced error code. Try to distribute your clothes evenly and restart it.

Conclusion

Troubleshooting a washing machine that spins but won’t drain can seem daunting, but with a little patience and these step-by-step instructions, you can often resolve the issue yourself. Remember to prioritize safety and follow the guidelines carefully. If you’ve exhausted these troubleshooting steps and the problem persists, it might be time to call a qualified appliance repair technician.

Youtube Video:


Quick Wiring Specifications & Terminal Guide

Component / Circuit Standard Wire Gauge Recommended Protection
Control & Trigger Signals 18 – 20 AWG 5A – 7.5A Inline Fuse
Standard Auxiliary Load 14 – 16 AWG 15A – 20A Circuit Breaker
Main Power Feed / Supply 10 – 12 AWG 30A – 40A Heavy-Duty Relay

Images References


Images References, Washing Machine Problems 6

Looking for more diagnostic guides? Explore our complete Washing Machine Problems 6 section for step-by-step troubleshooting solutions.

📚 Related Articles

Scroll to Top