Simpson Washing Machine Not Filling With Water

Introduction

Is your Simpson washing machine stubbornly refusing to fill with water? This is a frustrating problem that can halt your laundry routine and leave you with a pile of dirty clothes. Its especially annoying when youre in a hurry or have a whole familys worth of laundry to tackle. Dont panic! Often, it’s a simple issue you can resolve yourself without needing to call a costly repair technician. Addressing this promptly prevents potential damage to your machine and avoids unnecessary delays in getting your clothes clean.

Common Causes of simpson washing machine not filling with water

Here are some common reasons why your Simpson washing machine might not be filling with water:

• Closed Water Supply Valves: The most common oversight! Check if both the hot and cold water supply valves behind the machine are fully open.
• Kinked or Blocked Water Hoses: Hoses can become kinked, restricting water flow, or clogged with sediment.
• Clogged Inlet Filters: The water inlet valves have small filters that can get clogged with debris, preventing water from entering the machine.
• Faulty Water Inlet Valve: The water inlet valve controls the flow of water into the machine. If it’s defective, it might not open properly.
• Low Water Pressure: Insufficient water pressure to your house can prevent the machine from filling.
• Lid Switch Malfunction: The washing machine won’t fill if it thinks the lid or door is open. A faulty lid switch can cause this.
• Problem with Pressure Switch/Sensor: The machine may not fill water if it can not sense water level.
• Damaged or faulty electronic control board The electronic control board might have problem such as miscommunication.

Symptoms Checklist

Use this checklist to accurately identify the problem:

• The washing machine starts, but no water enters the drum.
• The washing machine fills very slowly.
• The washing machine makes a humming noise but doesn’t fill.
• Error codes related to water filling appear on the display panel.
• Water only fills for a very short time then stops.
• The machine fills partially then stops.

How to Fix simpson washing machine not filling with water Step-by-Step Guide

Follow these steps to troubleshoot your Simpson washing machine:

1. Check Water Supply Valves: Make sure both hot and cold water supply valves are fully open. Turn them counterclockwise.
2. Inspect Water Hoses: Look for kinks, bends, or damage in the hoses. Straighten any kinks and replace damaged hoses.
3. Clean Inlet Filters: Turn off the water supply. Disconnect the water hoses from the back of the machine. Locate the small filters inside the inlet valves (where the hoses connect). Use pliers to carefully remove the filters and clean them with a brush under running water. Reinstall the filters.
4. Check Water Pressure: Test the water pressure by disconnecting the hoses and running water into a bucket. You should have a strong, steady flow. If the pressure is low, contact your water company.
5. Inspect the Lid Switch: Locate the lid switch (usually near the door opening). Press it down manually. If the machine starts filling when you do this, the switch is likely faulty.
6. Run a Test Cycle: After checking the above, run a short wash cycle to see if the machine fills with water.
7. Check the Drain Hose: Ensure the drain hose is properly positioned and not inserted too far down the drainpipe, as this can create a siphoning effect.
8. Check the water inlet valve Disconnect power before doing anything. Test the water inlet valve using multimeter. See if there is continuity and power flowing to the valve when machine is supposed to fill water.
9. Inspect pressure hose This hose usually attached to bottom of washtub. Look for holes, disconnection or blockage.
10. Check for Error Codes: Consult your washing machine’s manual to understand the specific error code displayed and its corresponding solution.

Fix the Issue Without Buying Parts

Here are a few things you can try before considering replacement parts:

• Reset the Machine: Unplug the washing machine for 5-10 minutes to reset the internal computer. Plug it back in and try again.
• Clean the Dispenser Drawers: Remove and thoroughly clean the detergent and fabric softener dispenser drawers, as clogs can sometimes affect water flow.
• Check for Obstructions in the Drum: Make sure nothing is blocking the water jets inside the drum.
• Regular maintenance: Run a cleaning cycle with washing machine cleaner to remove buildup.

When Replacement Might Be Necessary

If you’ve tried all the above steps and your Simpson washing machine still isn’t filling, the water inlet valve or the lid switch might need replacing. A water inlet valve typically costs between $20 and $50, while a lid switch ranges from $15 to $30. A repair person can diagnose this issue and tell you if the control board need to be replaced which could cost $100 – $300. For more related activities, check out our Washer Making Loud Noise During Wash Cycle.

Safety Warning

• Always unplug the washing machine from the power outlet before performing any troubleshooting or repairs.
• Be careful when handling water and electricity to avoid electric shock.
• Turn off the water supply before disconnecting any hoses.
• If you are uncomfortable performing any of these steps, contact a qualified appliance repair technician.

Tools You May Need

• Pliers
• Screwdrivers (Phillips and flathead)
• Bucket
• Old toothbrush or small brush
• Multimeter

FAQ

Here are some frequently asked questions about washing machine filling problems:

• Q: Why is my washing machine filling very slowly?
  A: This is often caused by low water pressure or clogged inlet filters.
• Q: My washing machine hums but doesn’t fill. What’s wrong?
  A: This could indicate a faulty water inlet valve.
• Q: How do I know if the lid switch is bad?
  A: If the machine starts filling when you manually press the lid switch, it’s likely faulty.
• Q: Can I replace the water inlet valve myself?
  A: Yes, if you are comfortable with basic appliance repairs and follow safety precautions.

Conclusion

Don’t let a washing machine that won’t fill with water ruin your day! By following these troubleshooting steps, you can often diagnose and fix the problem yourself, saving time and money. Remember to always prioritize safety. If you’ve exhausted these solutions and your Simpson washing machine still refuses to fill, it might be time to call a qualified appliance repair technician for professional assistance. Good luck!

Youtube Video: