Samsung Washing Machine Empty Water

Introduction

Finding your Samsung washing machine won’t fill with water can be a frustrating experience. Clothes can’t be properly washed, and the machine just sits there, leaving you with a pile of laundry. This problem often happens because of simple issues, and identifying the cause quickly is important to prevent further inconvenience and potential damage to your clothing or the machine itself. Don’t worry, many of these problems are easy to resolve at home without needing to call a repair technician.

Common Causes of Samsung Washing Machine Empty Water

Here are some of the most common reasons why your Samsung washing machine might not be filling with water:. For more related activities, check out our Washer Is Not Draining Completely.

• Water Supply is Off: This might sound obvious, but it’s the most common oversight. Ensure both the hot and cold water supply valves connected to the washing machine are fully open.
• Kinked or Blocked Water Hoses: The hoses supplying water to your machine can become kinked or blocked with sediment, restricting water flow.
• Faulty Inlet Valve: The inlet valve controls the flow of water into the machine. If it’s defective, it might not open, even when the machine calls for water.
• Low Water Pressure: If the water pressure in your home is too low, the machine might not be able to fill properly.
• Blocked Water Inlet Filters: Small filters are usually located where the water hoses connect to the machine. These can become clogged with debris over time.
• Door/Lid Switch Malfunction: Most washing machines won’t fill if the door or lid switch isn’t properly engaged. A faulty switch can prevent the machine from starting the fill cycle.
• Control Board Issues: In some cases, a malfunctioning control board can prevent the machine from signaling the inlet valve to open.
• Drain Hose Issue: The drain hose is positioned too low creating a siphon effect that will pull the water out as it is filling.

Symptoms Checklist

Use this checklist to help pinpoint the problem:

• The washing machine starts, but no water enters the drum.
• A trickle of water enters the drum, but not enough to start the wash cycle.
• The machine makes a humming noise but doesn’t fill.
• You hear water flowing into the hoses, but it doesn’t reach the drum.
• Error codes related to water supply appear on the machine’s display panel.
• The washing machine worked fine previously, but suddenly stopped filling.

How to Fix Samsung Washing Machine Empty Water Step-by-Step Guide

Follow these steps to troubleshoot the issue:

1. Check the Water Supply: Make sure both the hot and cold water supply valves are fully open.
2. Inspect the Water Hoses: Check for kinks, bends, or damage in the hoses. Straighten any kinks and replace damaged hoses.
3. Check the Water Pressure: Test the water pressure at the faucet nearest to your washing machine. A weak flow suggests a problem with your home’s plumbing.
4. Clean the Inlet Filters: Turn off the water supply valves. Disconnect the water hoses from the washing machine. Use pliers to carefully remove the filters from the inlet valves. Clean the filters with a brush and rinse them thoroughly. Reinstall the filters and reconnect the hoses.
5. Inspect the Drain Hose: Make sure the drain hose is positioned correctly, not sitting on the floor.
6. Check the Door/Lid Switch: Ensure the door or lid closes securely. If it seems loose or damaged, inspect the switch mechanism. Sometimes cleaning the switch area can improve contact.
7. Run a Calibration Cycle (if applicable): Some Samsung washing machines have a calibration cycle that can help resolve sensor issues. Consult your owner’s manual for instructions.
8. Check for Error Codes: Refer to your owner’s manual to understand the meaning of any error codes displayed on the machine’s panel. Error codes often provide valuable clues about the problem.
9. Test the Inlet Valve (Advanced): Warning: If you’re uncomfortable working with electrical components, skip this step. Disconnect the power to the washing machine. Locate the inlet valve (usually near where the water hoses connect). Use a multimeter to test the valve’s solenoid for continuity. If there’s no continuity, the valve is likely faulty.
10. Check Water Pump for Debris: Look for access point (small door) where you might find debris causing the motor/pump not to work correctly.
11. Perform a Power Reset: Unplug the washing machine from the power outlet for at least 1 minute. Then, plug it back in and try running a wash cycle. This can sometimes reset the control board and resolve minor issues.

Fix the Issue Without Buying Parts

Here are some free methods that could help fix your washing machine:

• Reset the Machine: Unplug the machine for a minute, then plug it back in. This can clear minor errors.
• Clean the Filters Regularly: Clean the inlet filters every few months to prevent clogs.
• Check for Kinks: Straighten any kinks in the water hoses.
• Examine the Hose: Ensure your drain hose isn’t too far into the drain pipe as this can also create a siphon effect.

When Replacement Might Be Necessary

If you’ve tried all the troubleshooting steps and the washing machine still won’t fill, replacement of the inlet valve or, in rarer cases, the control board, might be necessary. An inlet valve typically costs between $30 and $75, while a control board can range from $100 to $300. If the machine is old or the repairs are costly, consider whether replacing the entire washing machine is a more cost-effective option in the long run.

Safety Warning

• Always unplug the washing machine from the power outlet before performing any repairs.
• Be careful when working with water to avoid electrical shock.
• If you’re uncomfortable working with electrical components, consult a qualified appliance repair technician.
• Clean up any spilled water immediately to prevent slips and falls.

Tools You May Need

• Pliers
• Screwdrivers (Phillips and flathead)
• Bucket
• Small brush
• Multimeter (optional, for testing the inlet valve)
• Towels

FAQ

Here are some frequently asked questions about washing machine water filling issues:

• Q: Why is my washing machine making noise but not filling? A: The inlet valve might be stuck or faulty, or the water supply could be blocked.
• Q: How do I know if my inlet valve is bad? A: Use a multimeter to test for continuity. If there’s no continuity, the valve is likely faulty.
• Q: Can low water pressure cause my washing machine not to fill? A: Yes, low water pressure can prevent the machine from filling properly.
• Q: What does error code [Example Error Code] mean? A: Refer to your owner’s manual to find the specific meaning of the error code.

Conclusion

Troubleshooting a Samsung washing machine that won’t fill with water can seem daunting, but by following these steps, you can often identify and resolve the problem yourself. Remember to start with the simplest solutions, such as checking the water supply and cleaning the filters. If you’ve exhausted all the troubleshooting steps and are still experiencing problems, it might be time to consult a qualified appliance repair technician. Good luck!

Youtube Video: