Samsung Washer How To Drain Water


Samsung Washer How To Drain Water

Introduction

A washing machine that won’t drain is a common and frustrating household problem. When your Samsung washer gets stuck with a tub full of water, it not only prevents you from doing laundry but can also lead to mold and mildew growth if left unattended. This guide will provide you with simple, step-by-step instructions to diagnose and resolve the issue, helping you save time and money by avoiding a costly service call. It’s important to address this issue promptly to prevent further damage to your appliance and your home.

💡 Technical Key Takeaways:

  • Core Focus: Diagnostic schematic and terminal connection layout for Samsung Washer How To Drain Water.
  • Target Scope: Field technicians, automotive DIYers, and residential/commercial electricians.
  • Safety Rule: Always disconnect the primary power source/battery terminal and verify zero voltage with a multimeter before touching wires.

Common Causes of Samsung Washer How to Drain Water

Here are some of the most frequent reasons why your Samsung washer might not be draining:

  • Clogged Drain Hose: This is often the primary culprit. Lint, small objects, or debris can accumulate in the drain hose, blocking the water flow.
  • Clogged Drain Pump Filter: The drain pump filter is designed to catch larger items before they damage the pump. If it’s full, it will prevent draining.
  • Kinked or Blocked Drain Hose: A kink in the hose restricts water flow. Also, the drain hose can get blocked where it connects to the standpipe in the wall.
  • Faulty Drain Pump: The drain pump is responsible for pushing water out of the washer. If it fails, the washer won’t drain.
  • Lid Switch Malfunction: In some models, a faulty lid switch can prevent the washer from entering the spin cycle (which is crucial for draining).
  • Control Board Issues: Though less common, a malfunctioning control board can prevent the drain cycle from initiating.
  • Air Lock in Drain Hose: Sometimes, an air pocket can form in the drain hose, preventing the water from flowing freely.
  • Over Sudsing: Using too much detergent, especially non-HE detergent, can cause excessive suds that interfere with the draining process.

Symptoms Checklist

Use this checklist to accurately identify the issue:

  • Washer is full of water after the wash cycle.
  • Washer makes a humming or buzzing noise but doesn’t drain.
  • Washer displays an error code related to draining (e.g., 5E, 5C, dE). Check your owner’s manual for the specific error code meaning.
  • Water drains very slowly or intermittently.
  • The drain hose feels blocked or kinked.
  • The drain pump filter is visibly clogged.

How to Fix Samsung Washer How to Drain Water Step-by-Step Guide

Follow these steps to troubleshoot and fix your draining issue:

  1. Unplug the Washer: For safety, always unplug the washer from the power outlet before starting any troubleshooting or repairs.
  2. Locate the Drain Hose: This is the hose that carries water away from the washer. It’s usually located at the back of the machine.
  3. Inspect the Drain Hose for Kinks: Make sure the drain hose is not kinked or bent, as this can restrict water flow. Straighten out any kinks you find.
  4. Check the Drain Hose Connection: Ensure the drain hose is properly connected to both the washer and the drain standpipe (the pipe in the wall).
  5. Remove the Drain Hose from the Standpipe: Carefully detach the drain hose from the standpipe.
  6. Check for Blockages in the Standpipe: Shine a flashlight into the standpipe to check for any obstructions. You can try using a plumbing snake or a long, flexible brush to clear any blockages.
  7. Clean the Drain Hose: Flush the drain hose with water to remove any debris. You can use a garden hose or a sink faucet.
  8. Locate the Drain Pump Filter: This is usually located at the bottom front of the washer, behind a small access panel. Refer to your owner’s manual for the exact location.
  9. Prepare for Water Spillage: Place a shallow pan or towels under the access panel to catch any water that may spill out.
  10. Open the Access Panel and Remove the Drain Pump Filter: Carefully unscrew and remove the drain pump filter. Be prepared for water to flow out.
  11. Clean the Drain Pump Filter: Remove any lint, debris, or small objects from the drain pump filter. Rinse it thoroughly with water.
  12. Inspect the Drain Pump: With the filter removed, look inside the drain pump housing for any visible obstructions. You can try using pliers to remove any large debris.
  13. Reinstall the Drain Pump Filter: Securely screw the drain pump filter back into place.
  14. Reconnect the Drain Hose to the Standpipe: Make sure the hose is securely attached.
  15. Plug in the Washer: Plug the washer back into the power outlet.
  16. Run a Rinse and Spin Cycle: Test the washer by running a rinse and spin cycle to see if it drains properly.

Fix the Issue Without Buying Parts

Before considering replacement parts, try these methods:

  • Reset the Washer: Unplug the washer for 5 minutes, then plug it back in. This can sometimes reset the control board and resolve the issue.
  • Clean the Washer: Run an empty wash cycle with a washing machine cleaner to remove soap buildup and residue.
  • Check Water Level Settings: Ensure that the water level setting is appropriate for the load size.
  • Avoid Oversudsing: Use only HE (High Efficiency) detergent and follow the manufacturer’s recommendations for dosage.

When Replacement Might Be Necessary

If the above steps don’t resolve the issue, the drain pump itself might be faulty and require replacement. A drain pump replacement typically costs between $50 and $150 for the part and potentially another $100-$200 for professional installation if you’re not comfortable doing it yourself. Other less common but potential replacement parts are the lid switch ($30-$70) and the control board (can be expensive, $150-$400). For more related activities, check out our Washer Making Loud Noise During Wash Cycle.

Safety Warning

  • Always unplug the washer from the power outlet before performing any maintenance or repairs.
  • Be careful when handling water; mop up any spills immediately to prevent slips and falls.
  • Avoid touching any electrical components with wet hands.
  • If you are uncomfortable performing any of these steps, consult a qualified appliance repair technician.

Tools You May Need

  • Pliers
  • Screwdrivers (Phillips and flathead)
  • Shallow pan or towels
  • Flashlight
  • Plumbing snake (optional)

FAQ

Here are some frequently asked questions:

  • Q: My washer is making a loud humming noise but not draining. What does this mean?
    A: This usually indicates a problem with the drain pump. It could be clogged or faulty. Check the drain pump filter first, and if that doesn’t help, the pump may need to be replaced.
  • Q: How often should I clean the drain pump filter?
    A: It’s recommended to clean the drain pump filter every 1-3 months, depending on how frequently you use your washer.
  • Q: What is HE detergent, and why is it important?
    A: HE (High Efficiency) detergent is specially formulated for use in high-efficiency washing machines. It produces fewer suds, which prevents over-sudsing and ensures proper draining.
  • Q: My washer is displaying an error code. Where can I find out what it means?
    A: Refer to your owner’s manual for a list of error codes and their corresponding meanings. You can also search online using your washer’s model number.

Conclusion

Troubleshooting a Samsung washer that won’t drain can seem daunting, but by following these steps, you can often resolve the issue yourself. Remember to always prioritize safety and consult your owner’s manual for specific instructions. If you’ve tried these solutions and your washer is still not draining, it might be time to call a qualified appliance repair technician. Good luck!

Quick Wiring Specifications & Terminal Guide

Component / Circuit Standard Wire Gauge Recommended Protection
Control & Trigger Signals 18 – 20 AWG 5A – 7.5A Inline Fuse
Standard Auxiliary Load 14 – 16 AWG 15A – 20A Circuit Breaker
Main Power Feed / Supply 10 – 12 AWG 30A – 40A Heavy-Duty Relay

Images References


Images References, Washing Machine Problems 5

Looking for more diagnostic guides? Explore our complete Washing Machine Problems 5 section for step-by-step troubleshooting solutions.

📚 Related Articles

Scroll to Top