Maytag Washer Has Water In Drum

Introduction

Finding standing water in your Maytag washer after a cycle is complete is a common problem. This indicates that the water isn’t draining properly, which can lead to musty odors, potential mildew growth, and even damage to your clothes. Addressing this issue quickly is important to prevent further complications and maintain the lifespan of your washing machine. Let’s get it sorted out!

Common Causes of maytag washer has water in drum

Here are some potential reasons why your Maytag washer might have water in the drum:

• Clogged Drain Hose: A blockage in the drain hose restricts water flow.
• Drain Pump Issues: A faulty or clogged drain pump is unable to expel the water effectively.
• Clogged Drain Filter: Many washers have a filter to catch lint and debris; a full filter slows drainage.
• Kinked or Blocked Drain Hose: A kink or obstruction in the hose can stop water from flowing out.
• Air Lock in the Drain Hose: Sometimes air trapped in the drain hose can prevent proper siphoning.
• Faulty Water Inlet Valve: A leaky inlet valve might be dripping water into the drum even when the washer is off.
• Level Sensor Problems: A malfunctioning water level sensor might not be signaling the washer to drain.
• Control Board Malfunction: In rare cases, a faulty control board might be preventing the drain cycle from initiating.

Symptoms Checklist

Check for these indicators to accurately identify the problem:

• Water remains in the drum after a wash cycle.
• The washer makes unusual noises during the drain cycle.
• The drain cycle seems to take longer than usual.
• Error codes related to draining appear on the washer’s display.
• You notice a foul odor coming from the washer.

How to Fix maytag washer has water in drum Step-by-Step Guide

Follow these steps to troubleshoot and resolve the issue:

1. Unplug the Washer: Disconnect the washer from the power outlet for safety.
2. Check the Drain Hose: Locate the drain hose at the back of the washer. Ensure it’s not kinked, crushed, or bent. Straighten any kinks.
3. Inspect the Drain Hose Connection: Detach the drain hose from the drainpipe or standpipe. Check for clogs at the connection point.
4. Flush the Drain Hose: Hold the drain hose over a bucket and run water through it to dislodge any potential blockages.
5. Locate the Drain Filter: Most Maytag washers have a drain filter, often located at the bottom front of the machine behind a small access panel. Refer to your owner’s manual for the exact location.
6. Clean the Drain Filter: Carefully remove the drain filter (have a towel ready as some water will spill). Clean it thoroughly under running water to remove lint, hair, and debris.
7. Check the Drain Pump (if accessible): Some washers allow access to the drain pump. Inspect the pump for any obstructions. Caution: This step might require some disassembly; proceed with caution if you’re not comfortable.
8. Test the Drain Pump (Advanced): If you can access the pump, you can carefully test it for continuity with a multimeter (if you have one and know how to use it). This confirms if the pump motor is receiving power. Consult your washer’s repair manual for specifics on testing the drain pump.
9. Check the Air Gap (if applicable): Some plumbing setups include an air gap. Make sure it is not clogged, preventing proper drainage.
10. Run a Rinse and Spin Cycle: After clearing any potential obstructions, run a rinse and spin cycle to test if the washer is draining correctly.
11. Level the Washer: Ensure your washer is level. An unlevel washer can sometimes affect drainage. Use a level and adjust the legs as needed.
12. Check the Water Inlet Valve: With the washer off and disconnected from the power, carefully inspect the water inlet valves (where the water supply hoses connect) for any signs of leakage or dripping. If a valve is leaking, it might be causing the water level in the drum to rise.

Fix the Issue Without Buying Parts

Here are some things you can try before considering part replacement:

• Washer Reset: Unplug the washer for at least one minute to reset the control board.
• Deep Cleaning: Run an empty wash cycle with a washing machine cleaner to remove buildup that could be affecting drainage.
• Drain Hose Maintenance: Periodically flush the drain hose with hot water to prevent future clogs.
• Preventative Care: Use the correct amount of detergent to prevent excessive suds that can interfere with draining.
• Load Management: Avoid overloading the washer, as this can strain the drain pump.

When Replacement Might Be Necessary

If you’ve tried all the troubleshooting steps and the washer still doesn’t drain, consider the following:

• Drain Pump Replacement: A faulty drain pump is a common cause of drainage issues. Replacement costs typically range from $50 to $150.
• Water Level Sensor Replacement: If the sensor is defective, the control board may not initiate the drain cycle. These sensors generally cost between $30 and $80.
• Control Board Replacement: In rare cases, a faulty control board can cause drainage problems. Control boards are the most expensive part, typically costing between $150 and $300. However, have a technician diagnose this before replacing it.

Safety Warning

• Always unplug the washer from the power outlet before performing any maintenance or repairs.
• Be careful when working with water to avoid electrical shock.
• Wear gloves when handling potentially dirty or contaminated parts.
• If you’re uncomfortable with any of these steps, contact a qualified appliance repair technician.

Tools You May Need

• Screwdrivers (Phillips and flathead)
• Pliers
• Bucket
• Towels
• Adjustable wrench
• Level
• Multimeter (optional, for testing drain pump continuity)

FAQ

Here are some frequently asked questions about washers not draining:

• Q: Why is my washer making a loud noise when it tries to drain?

  A: This could indicate a blockage in the drain pump or drain hose. Check for obstructions.

• Q: How often should I clean the drain filter?

  A: It’s recommended to clean the drain filter every 1-3 months, depending on usage.

• Q: Can I use a plumbing snake to clear a drain hose blockage?

  A: Yes, but be very careful not to damage the drain hose. Start with gentle probing.

• Q: What does it mean when my washer displays an “LF” or “F05” error code?

  A: These codes often indicate a drainage problem. Consult your owner’s manual for specific code definitions.

Conclusion

Troubleshooting a Maytag washer with water in the drum can seem daunting, but by following these steps, you can often resolve the issue yourself. Remember to always prioritize safety and consult your owner’s manual for specific instructions related to your model. If you’ve exhausted these troubleshooting steps and the problem persists, don’t hesitate to contact a qualified appliance repair technician for professional assistance. Good luck!

Youtube Video: