Lg Tromm Washer Not Filling Water

Introduction

Discovering your LG Tromm washer isn’t filling with water can be a frustrating surprise, especially when you’re eager to get laundry done. This issue prevents your clothes from getting properly cleaned, leaving you with a pile of unwashed items. Addressing this problem promptly is important to avoid further inconvenience and potential damage to your washing machine. This guide will help you troubleshoot the most common causes and guide you through easy-to-understand solutions.

Common Causes of LG Tromm Washer Not Filling Water

Here are several reasons why your LG Tromm washer might not be filling with water:

• Closed Water Valves: The water supply valves behind your washer might be turned off.
• Kinked or Blocked Water Hoses: The hoses that connect the water supply to your washer could be bent, pinched, or blocked by debris.
• Clogged Inlet Filters: Small filters located at the water inlet valves on the back of the washer can become clogged with sediment and mineral deposits.
• Low Water Pressure: Insufficient water pressure in your home can prevent the washer from filling properly.
• Faulty Water Inlet Valve: The water inlet valve controls the flow of water into the washer. If it fails, it may not open.
• Defective Pressure Switch: This switch senses the water level in the drum. If it’s faulty, it might incorrectly signal that the washer is full.
• Door/Lid Switch Malfunction: In some cases, a faulty door or lid switch can prevent the washer from starting the fill cycle.
• Control Board Issues: Although less common, a malfunctioning control board could prevent the water inlet valve from opening.

Symptoms Checklist

Use this checklist to accurately identify your specific situation:

• The washer starts, but no water enters the drum.
• The washer makes a humming or buzzing sound but doesn’t fill.
• The washer fills very slowly.
• Error codes related to water supply (e.g., “IE,” “OE”) are displayed.
• The washer fills intermittently.

How to Fix LG Tromm Washer Not Filling Water Step-by-Step Guide

1. Turn off the Washer: Unplug the washer from the power outlet for safety.
2. Check the Water Supply Valves: Ensure both the hot and cold water valves behind the washer are fully open.
3. Inspect the Water Hoses: Look for any kinks, bends, or crushing in the hoses. Straighten them out or replace them if damaged.
4. Clean the Inlet Filters:
   • Turn off the water supply.
   • Disconnect the water hoses from the back of the washer.
   • Locate the small filters inside the inlets.
   • Use pliers to gently remove the filters.
   • Clean the filters with a brush and running water to remove any debris.
   • Reinstall the filters and reconnect the water hoses.
5. Check Water Pressure: Test the water pressure by connecting a hose to the faucet and checking the flow. If it’s weak, contact your local water utility.
6. Check the Door/Lid Switch: Make sure the door or lid closes properly and that the switch is engaging. If it appears damaged, further testing may be required.
7. Run a Test Cycle: Plug the washer back in and run a short wash cycle to see if it fills with water.
8. Check Error Codes: Consult your washer’s manual for any error codes displayed and follow the recommended troubleshooting steps.
9. Reset the Washer: Unplug the washer for 5-10 minutes to reset the control board. Plug it back in and try again.
10. Check the Drain Hose: Ensure the drain hose isn’t inserted too far into the drain pipe, as this can sometimes siphon water out as it enters.

Fix the Issue Without Buying Parts

Many water filling problems can be resolved without replacing parts:

• Resetting: As mentioned above, a simple reset can sometimes clear temporary glitches.
• Cleaning: Regular cleaning of the inlet filters and hoses can prevent blockages.
• Recalibration (If Applicable): Some washers have a recalibration cycle in the settings menu. Check your owner’s manual.
• Inspection: Regularly inspect hoses for wear and tear and ensure proper valve operation.
• Proper loading of clothes: Avoid overloading the machine which can affect water level sensing.

When Replacement Might Be Necessary

If the troubleshooting steps above don’t resolve the issue, you might need to consider replacing certain parts. The most common parts that fail are the water inlet valve and the pressure switch. Replacement costs can range from $50 to $200 USD, depending on the part and the model of your washer. However, if you are not confident with electrical or mechanical repair, hiring a qualified appliance repair technician is a safer option.

Safety Warning

• Always unplug the washer from the power outlet before performing any repairs.
• Turn off the water supply to the washer before disconnecting any hoses.
• Avoid working on electrical components with wet hands.
• Be careful when handling tools to avoid injury.
• If you’re uncomfortable with any step, consult a qualified appliance repair technician.

Tools You May Need

• Pliers
• Screwdrivers (Phillips and flathead)
• Adjustable wrench
• Bucket
• Small brush

FAQ

Here are some frequently asked questions:

• Q: My washer fills slowly. What could be the problem? A: This is often caused by low water pressure or clogged inlet filters.
• Q: I hear a buzzing sound when the washer should be filling, but no water comes in. What could that be? A: The water inlet valve might be faulty and not opening.
• Q: How do I know if my water inlet valve is bad? A: You can test the valve with a multimeter for continuity, or visually inspect it for damage. If youre not comfortable doing this, call a technician.
• Q: I cleaned the inlet filters, but the washer still doesn’t fill. What should I do next? A: Check the water pressure and inspect the water hoses for kinks or blockage.

Conclusion

Troubleshooting an LG Tromm washer that isn’t filling with water can seem daunting, but by following these steps, you can often identify and resolve the problem yourself. Remember to prioritize safety and take your time. If you’ve tried these steps and your washer still isn’t working, it might be time to call a qualified appliance repair technician for professional assistance. Good luck!

Youtube Video: