Kitchenaid Freezer Not Working But Fridge Is


Kitchenaid Freezer Not Working But Fridge Is

Introduction

Discovering that your KitchenAid freezer isn’t freezing but your refrigerator is can be a frustrating surprise. This usually means the freezer isn’t cold enough to properly store food, leading to potential spoilage and wasted groceries. This issue often occurs when airflow is restricted or a component isn’t functioning correctly. Acting quickly to diagnose and fix the problem can save you money and prevent further damage to your appliance.

💡 Technical Key Takeaways:

  • Core Focus: Diagnostic schematic and terminal connection layout for Kitchenaid Freezer Not Working But Fridge Is.
  • Target Scope: Field technicians, automotive DIYers, and residential/commercial electricians.
  • Safety Rule: Always disconnect the primary power source/battery terminal and verify zero voltage with a multimeter before touching wires.

Common Causes of KitchenAid Freezer Not Working But Fridge Is

Here are some common culprits behind a KitchenAid freezer failing while the fridge section works:

  • Dirty Condenser Coils: Dust and debris on the condenser coils hinder heat release, making the freezer work harder.
  • Frost Buildup: Excessive frost in the freezer can block airflow and prevent proper cooling.
  • Faulty Door Seal: A damaged or improperly sealing door allows warm air to enter, raising the freezer’s temperature.
  • Blocked Air Vents: Obstructions within the freezer or refrigerator can restrict the flow of cold air.
  • Defective Damper Control: The damper controls the amount of cold air flowing from the freezer to the refrigerator. A faulty damper might not open properly.
  • Failed Evaporator Fan Motor: The evaporator fan circulates cold air within the freezer. If it’s not running, the freezer won’t cool effectively.
  • Overloaded Freezer: Packing the freezer too full can restrict airflow and reduce its cooling efficiency.
  • Temperature Setting Issues: An incorrectly set temperature control can prevent the freezer from reaching its desired temperature.
  • Start Relay Problem: The start relay helps the compressor start up. If it’s faulty, the compressor may not run, affecting cooling.

Symptoms Checklist

Use this checklist to accurately identify the problem:

  • The freezer compartment is warmer than usual.
  • Food in the freezer is thawing or not frozen solid.
  • The refrigerator compartment is cooling normally.
  • You hear unusual noises coming from the refrigerator, such as clicking or buzzing.
  • There is excessive frost buildup in the freezer.
  • The refrigerator runs constantly.
  • The freezer door doesn’t seal tightly.

How to Fix KitchenAid Freezer Not Working But Fridge Is Step-by-Step Guide

Follow these steps to troubleshoot your KitchenAid freezer:

  1. Check the Temperature Settings: Ensure the freezer temperature is set correctly (usually around 0F or -18C).
  2. Inspect the Door Seal: Examine the door seal for any damage, cracks, or gaps. Clean the seal with warm, soapy water.
  3. Clean the Condenser Coils: Locate the condenser coils (usually on the back or bottom of the refrigerator) and clean them with a vacuum cleaner and brush attachment.
  4. Defrost the Freezer: If there’s excessive frost buildup, manually defrost the freezer by unplugging the refrigerator and leaving the door open for several hours.
  5. Check the Air Vents: Make sure the air vents inside the freezer and refrigerator are not blocked by food items.
  6. Examine the Evaporator Fan: Open the freezer and listen for the evaporator fan running. If you don’t hear it, the fan motor may be faulty. (You can usually access the fan by removing a back panel inside the freezer).
  7. Inspect the Damper Control: The damper is usually located between the freezer and refrigerator compartments. Make sure it’s opening and closing freely.
  8. Check the Start Relay and Overload: These are typically near the compressor, unplug the unit and remove the access panel. Test with a multimeter if you are comfortable; visually inspect for burnt components.
  9. Reduce Freezer Load: Remove any unnecessary items from the freezer to improve airflow.
  10. Check the Voltage: Make sure the refrigerator is receiving the correct voltage from the outlet.
  11. Unplug and Reset: Unplug the refrigerator for 30 minutes, then plug it back in. This can sometimes reset the control board.
  12. Listen to the Compressor: Is the compressor running? If not it can be a sign that there is a problem with it and can require replacement.

Fix the Issue Without Buying Parts

Before considering replacements, try these free methods:

  • Reset: Unplug the refrigerator for 30 minutes to reset the system.
  • Cleaning: Regularly clean the condenser coils and door seals to maintain efficiency.
  • Recalibration (if available): Some models have recalibration options in their control panel; check your owner’s manual.
  • Inspection Tips: Regularly inspect the interior for frost buildup and airflow obstructions.
  • Maintenance Basics: Avoid overloading the freezer and ensure proper ventilation around the refrigerator.

When Replacement Might Be Necessary

If the problem persists after troubleshooting, replacing certain parts might be necessary. The evaporator fan motor, damper control, or even the compressor are common culprits. Replacing the evaporator fan motor might cost between $50 and $150. A new damper control can range from $30 to $80. Compressor replacement is a more significant expense, potentially costing between $300 and $700, including labor. Consult with a qualified appliance repair technician for accurate diagnosis and replacement.

Safety Warning

Please observe these safety precautions:

  • Always unplug the refrigerator before performing any repairs.
  • Avoid working on the refrigerator with wet hands or on a wet floor.
  • Be careful when handling electrical components.
  • If you are not comfortable performing repairs, consult a qualified technician.

Tools You May Need

Here are some basic tools that might be useful:

  • Screwdrivers (Phillips and flathead)
  • Vacuum cleaner with brush attachment
  • Multimeter (for testing electrical components)
  • Wrench Set
  • Pliers

FAQ

Here are some frequently asked questions:

  • Q: Why is my freezer warm but the fridge is cold? A: It could be due to blocked air vents, a faulty damper control, or a problem with the evaporator fan.
  • Q: How often should I clean the condenser coils? A: Ideally, clean the condenser coils every 6 months.
  • Q: Can I fix a faulty door seal? A: Small tears can be repaired with sealant, but larger damage may require replacing the entire seal.
  • Q: What is the ideal temperature for my freezer? A: The ideal freezer temperature is around 0F (-18C).
  • Q: How do I know if my compressor is failing? A: Signs include the refrigerator not cooling, unusual noises, or the compressor not running at all.

Conclusion

Troubleshooting a KitchenAid freezer that isn’t working while the fridge is can seem daunting, but by following these steps, you can often diagnose and resolve the issue yourself. Try the simple fixes first, and don’t hesitate to consult a professional if the problem persists. Addressing this issue promptly can save you from food spoilage and costly repairs down the line. Hopefully, this will guide you and you will not need a technician to fix the problem.

Youtube Video:


Quick Wiring Specifications & Terminal Guide

Component / Circuit Standard Wire Gauge Recommended Protection
Control & Trigger Signals 18 – 20 AWG 5A – 7.5A Inline Fuse
Standard Auxiliary Load 14 – 16 AWG 15A – 20A Circuit Breaker
Main Power Feed / Supply 10 – 12 AWG 30A – 40A Heavy-Duty Relay

Images References


Images References, Refrigerator Problems 1

Looking for more diagnostic guides? Explore our complete Refrigerator Problems 1 section for step-by-step troubleshooting solutions.

📚 Related Articles

Scroll to Top