Introduction
A washing machine full of water after a cycle is a common and frustrating problem. When your Kenmore washer won’t drain completely, it prevents you from transferring clothes to the dryer, potentially leading to mold and mildew. Addressing this issue quickly is important to prevent further damage and get your laundry routine back on track.
💡 Technical Key Takeaways:
- Core Focus: Diagnostic schematic and terminal connection layout for Kenmore Washer Not Draining Completely.
- Target Scope: Field technicians, automotive DIYers, and residential/commercial electricians.
- Safety Rule: Always disconnect the primary power source/battery terminal and verify zero voltage with a multimeter before touching wires.
Common Causes of kenmore washer not draining completely
Here are several common reasons why your Kenmore washer might not be draining properly:
- Clogged Drain Hose: A kinked or blocked drain hose restricts water flow.
- Clogged Drain Pump Filter: Debris like lint, hair, and small objects can accumulate in the drain pump filter.
- Faulty Drain Pump: The drain pump motor may be failing, preventing it from pushing water out.
- Blocked Drainpipe: A blockage in the house drainpipe can back up into the washer.
- Kinked or Twisted Tub Drain Hose: The hose connecting the washer tub to the drain pump could be twisted or restricted.
- Air Lock in Drain System: Air trapped in the drain hose can prevent proper water flow.
- Lid Switch Malfunction (for Top-Loaders): If the lid switch is faulty, the washer may not complete the spin cycle, leading to standing water.
- Control Board Issues: Although less common, a malfunctioning control board could prevent the drain cycle from initiating.
Symptoms Checklist
Look for these indicators to confirm the drainage problem:
- Water remains in the washer drum after the cycle completes.
- The washer makes a humming or buzzing sound during the drain cycle, but no water is expelled.
- The washer stops mid-cycle and displays an error code related to draining.
- The drain hose vibrates excessively but little to no water comes out.
- The drain cycle seems to take much longer than usual.
How to Fix kenmore washer not draining completely Step-by-Step Guide
Follow these steps to troubleshoot and fix your Kenmore washer:
- Unplug the Washer: Disconnect the washer from the power outlet for safety.
- Check the Drain Hose: Inspect the drain hose for kinks, bends, or obstructions. Straighten any kinks and ensure the hose isn’t crushed.
- Detach the Drain Hose: Carefully detach the drain hose from the drainpipe or standpipe.
- Check for Blockages in the Drain Hose: Flush the drain hose with water to dislodge any debris. You can also use a long, flexible brush or wire to clear obstructions.
- Inspect the Drainpipe: Make sure the drainpipe isn’t clogged. You can try using a plumbing snake or drain cleaner (follow product instructions carefully).
- Locate the Drain Pump Filter: The filter is usually located at the front, bottom corner of the washer behind a small access panel. Consult your owner’s manual for the exact location.
- Drain the Remaining Water: Before opening the drain pump filter, place a shallow container or towels to catch any spilled water.
- Clean the Drain Pump Filter: Carefully remove the drain pump filter and clean it thoroughly, removing any lint, hair, or small objects.
- Reinstall the Drain Pump Filter: Securely reattach the drain pump filter.
- Check the Tub Drain Hose: Access the area where the tub connects to the drain pump (you may need to remove an access panel). Inspect the hose for kinks or blockages.
- Check the Lid Switch (Top-Loaders Only): Manually depress the lid switch to see if the washer attempts to drain. If not, the switch might be faulty. You can usually locate the lid switch under the lid of the washing machine, it is usually behind a small pannel.
- Check for Air Lock: Reattach the drain hose loosely to the drain pipe. Run a rinse cycle. The loose connection may allow air to escape.
- Plug in the Washer: Reconnect the washer to the power outlet.
- Run a Test Cycle: Run a short rinse and spin cycle to see if the washer drains properly.
Fix the Issue Without Buying Parts
Often, you can resolve draining issues without replacing parts:
- Reset the Washer: Unplug the washer for 1-2 minutes, then plug it back in. This can sometimes reset the control board.
- Deep Cleaning: Regular cleaning with a washer cleaner can prevent lint and debris buildup.
- Leveling the Washer: Ensure the washer is level. An unlevel washer can sometimes affect the drain cycle.
- Avoid Overloading: Overloading the washer can strain the drain pump.
- Check for Small Items: Look for socks, coins, or other small items that may be lodged in the pump area.
When Replacement Might Be Necessary
If the above steps don’t work, the following parts might need replacement:
- Drain Pump: If the drain pump is consistently failing, replacement is likely necessary. Cost: $50-$150.
- Lid Switch (Top-Loaders): If the lid switch is faulty, the washer won’t complete the spin cycle. Cost: $20-$50.
- Control Board: If all other components check out, the control board might be the issue. Cost: $100-$300. Consider professional diagnostics before replacing the control board.
Safety Warning
- Always unplug the washer before performing any maintenance or repairs.
- Be careful when handling water to avoid slips and falls.
- If you’re uncomfortable working with electrical components, consult a qualified technician.
- Be careful of sharp edges when removing access panels.
Tools You May Need
- Screwdrivers (Phillips and flathead)
- Pliers
- Bucket or shallow container
- Towels
- Flashlight
- Plumbing snake (optional)
- Flexible brush or wire
FAQ
Here are some frequently asked questions:
- Why is my washer humming but not draining? A humming sound usually indicates the drain pump is trying to work but is blocked. Check the drain pump filter.
- What does an error code related to draining mean? Error codes vary by model. Consult your owner’s manual to identify the specific issue.
- How often should I clean the drain pump filter? It’s recommended to clean the drain pump filter every 1-3 months, depending on usage.
- Can overloading the washer cause draining problems? Yes, overloading can strain the drain pump and lead to incomplete draining.
Conclusion
Troubleshooting a Kenmore washer that won’t drain completely can seem daunting, but by following these steps, you can often identify and resolve the issue yourself. Start with the simple solutions, such as checking the drain hose and cleaning the filter. If the problem persists, consider more complex troubleshooting. If you’re uncomfortable with any of these steps, don’t hesitate to call a qualified appliance repair technician. Good luck!
Youtube Video:
Quick Wiring Specifications & Terminal Guide
| Component / Circuit | Standard Wire Gauge | Recommended Protection |
|---|---|---|
| Control & Trigger Signals | 18 – 20 AWG | 5A – 7.5A Inline Fuse |
| Standard Auxiliary Load | 14 – 16 AWG | 15A – 20A Circuit Breaker |
| Main Power Feed / Supply | 10 – 12 AWG | 30A – 40A Heavy-Duty Relay |
Images References
Looking for more diagnostic guides? Explore our complete Washing Machine Problems 1 section for step-by-step troubleshooting solutions.
