Kenmore Washer Makes Loud Noise When Agitating


Kenmore Washer Makes Loud Noise When Agitating

Introduction

A loud noise emanating from your Kenmore washing machine specifically when it’s agitating (moving the clothes back and forth during the wash cycle) is a common problem homeowners face. It matters because ignoring it can lead to further damage and potentially more expensive repairs down the line. It often occurs when the machine is fully loaded or washing bulky items. Addressing the noise promptly can prevent a minor issue from becoming a major breakdown.

💡 Technical Key Takeaways:

  • Core Focus: Diagnostic schematic and terminal connection layout for Kenmore Washer Makes Loud Noise When Agitating.
  • Target Scope: Field technicians, automotive DIYers, and residential/commercial electricians.
  • Safety Rule: Always disconnect the primary power source/battery terminal and verify zero voltage with a multimeter before touching wires.

Common Causes of Kenmore Washer Makes Loud Noise When Agitating

Here are some of the most frequent reasons your Kenmore washer might be making a racket while agitating:. For more related activities, check out our My Washer Makes A Grinding Noise.

  • Loose Objects: Coins, buttons, or other small items trapped in the agitator or between the drum and the outer tub.
  • Worn Agitator Dogs (or Cogs): These small parts inside the agitator assembly allow it to move in one direction. When worn, they can cause a clicking or ratcheting sound.
  • Agitator Rubbing: The agitator might be rubbing against the wash tub or another component.
  • Drive Block (or Agitator Coupler) Wear: This part connects the motor to the agitator. Wear and tear can cause slippage and noise.
  • Worn Tub Bearing: Located at the bottom of the outer tub, a worn bearing can create a grinding or roaring sound, especially during agitation.
  • Damaged Drive Pulley: If the drive pulley is cracked or damaged, it can cause the belt to slip and create a squealing or grinding noise.
  • Loose Pump Belt: A loose belt connecting the motor to the water pump can vibrate and cause noise.
  • Overloading the Washer: Putting too many clothes in the washer can strain the components and cause noise.

Symptoms Checklist

Use this checklist to help pinpoint the issue:

  • Noise only occurs during the agitation cycle.
  • Noise is a grinding, clicking, squealing, or banging sound.
  • The washer shakes excessively during agitation.
  • You notice metallic sounds or rattling.
  • Agitation seems weak or ineffective.
  • The washer smells like burning rubber.

How to Fix Kenmore Washer Makes Loud Noise When Agitating Step-by-Step Guide

Before starting any repair, always unplug your washing machine!

  1. Inspect for Loose Objects: Carefully check the agitator and the space between the inner wash tub and the outer tub for any trapped objects like coins, buttons, or socks. Use pliers or tweezers to remove them.
  2. Check Agitator Movement: With the washer off, manually rotate the agitator. Does it move smoothly in one direction and ratchet freely in the other? If not, the agitator dogs might be worn.
  3. Examine the Agitator Assembly: Some agitators have a removable top. Check underneath for damage or debris.
  4. Inspect the Drive Block (Agitator Coupler): This part connects the motor to the agitator. It’s typically located under the agitator. Check for cracks, wear, or broken pieces. This often involves removing the agitator.
  5. Access the Motor Area (If Comfortable): Only if you are comfortable and confident in your abilities Tip the washer back to access the motor and pump area. (Consider having someone help you.)
  6. Inspect the Drive Pulley: Look for any cracks, warping, or damage to the drive pulley. Ensure it’s securely attached to the motor shaft.
  7. Check the Pump Belt: While you’re in the motor area, check the pump belt for looseness or wear. It should be snug, but not overly tight.
  8. Listen Carefully: With the washer unplugged, try manually spinning the tub. Listen for any grinding or scraping sounds that might indicate a worn tub bearing. This is often a more advanced repair.
  9. Level the Washer: Ensure your washer is properly leveled. Use a level to check the top of the washer in both directions. Adjust the legs as needed until it’s level. An uneven washer can vibrate excessively.
  10. Check the Suspension System: Many washers have suspension rods or springs that help stabilize the tub. Make sure these are properly attached and in good condition. Broken or detached suspension components can cause excessive shaking and noise.
  11. Clean the Wash Tub: Over time, detergent residue and mineral buildup can accumulate in the wash tub. Run an empty wash cycle with a washing machine cleaner to remove buildup.
  12. Reduce Load Size: Overloading the washer puts extra strain on the components. Try washing smaller loads to see if the noise diminishes.

Fix the Issue Without Buying Parts

Often, simple steps can resolve the noise without needing to buy new parts:

  • Reset the Washer: Unplug the washer for a few minutes, then plug it back in. This can sometimes reset the control board and resolve minor glitches.
  • Cleaning: As mentioned earlier, clean the wash tub regularly.
  • Inspection: Regularly inspect for loose objects or signs of wear. Early detection can prevent bigger problems.
  • Proper Loading: Always load the washer according to the manufacturer’s instructions. Avoid overloading.

When Replacement Might Be Necessary

If the noise persists after trying the above steps, or if you identify a severely damaged part, replacement might be necessary. Common parts that fail include:

  • Agitator Dogs/Cogs: ($10-$20)
  • Drive Block (Agitator Coupler): ($15-$30)
  • Tub Bearing: ($50-$150 + Labor – This is a complex repair.)
  • Drive Pulley: ($20-$50)
  • Pump Belt: ($10-$20)

Safety Warning

  • Always unplug the washing machine before performing any repairs.
  • Be careful when tilting the washer. Have someone help you to avoid injury.
  • Avoid working on the washer if the floor is wet to prevent electric shock.
  • If you are uncomfortable with any of these steps, consult a qualified appliance repair technician.

Tools You May Need

  • Screwdrivers (Phillips and flathead)
  • Pliers
  • Socket set
  • Wrench set
  • Gloves
  • Flashlight
  • Level

FAQ

Here are some frequently asked questions:

  • Q: Why is my washer only noisy when agitating, not spinning? A: Agitation involves a specific set of parts (agitator, drive block, etc.) that are only used during the wash cycle. The noise likely originates from one of these parts.
  • Q: Can I still use the washer if it’s making noise? A: It’s generally not recommended to continue using the washer if it’s making a loud noise. It could cause further damage.
  • Q: How can I tell if the tub bearing is bad? A: A bad tub bearing usually makes a grinding or roaring noise, especially during agitation and spin cycles. You might also feel excessive vibration.
  • Q: Is it cheaper to repair or replace a noisy washer? A: It depends on the age of the washer and the cost of the repair. If the washer is old and the repair is expensive (e.g., tub bearing replacement), replacement might be a better option.
  • Q: What does it mean when the washer smells like burning rubber?A: Usually this indicated a worn or damaged belt – it should be replaced immediatly.

Conclusion

Troubleshooting a noisy washing machine can seem daunting, but by following these steps, you can often identify and resolve the issue yourself. Remember to prioritize safety and take your time. If you’ve exhausted these troubleshooting steps and the noise persists, don’t hesitate to call a qualified appliance repair technician for professional assistance. Good luck!

Youtube Video:


Quick Wiring Specifications & Terminal Guide

Component / Circuit Standard Wire Gauge Recommended Protection
Control & Trigger Signals 18 – 20 AWG 5A – 7.5A Inline Fuse
Standard Auxiliary Load 14 – 16 AWG 15A – 20A Circuit Breaker
Main Power Feed / Supply 10 – 12 AWG 30A – 40A Heavy-Duty Relay

Images References


Images References, Washing Machine Problems 4

Looking for more diagnostic guides? Explore our complete Washing Machine Problems 4 section for step-by-step troubleshooting solutions.

📚 Related Articles

Scroll to Top