Introduction
A Kenmore washer refusing to drain is a common and frustrating problem for homeowners. The drain pump, responsible for removing water after the wash cycle, is often the culprit. When it fails, your clothes stay soaking wet, and your laundry routine grinds to a halt. Addressing this quickly is essential to prevent mold growth, water damage, and further appliance issues. Let’s explore the problem of a Kenmore washer drain pump and how you can fix it yourself.
💡 Technical Key Takeaways:
- Core Focus: Diagnostic schematic and terminal connection layout for Kenmore Washer Drain Pump Problem.
- Target Scope: Field technicians, automotive DIYers, and residential/commercial electricians.
- Safety Rule: Always disconnect the primary power source/battery terminal and verify zero voltage with a multimeter before touching wires.
Common Causes of Kenmore Washer Drain Pump Problem
Several factors can cause your Kenmore washer’s drain pump to malfunction:
- Clogged Drain Hose: A blocked hose prevents water from exiting.
- Obstructed Drain Pump: Small items like coins, buttons, or lint can get stuck in the pump.
- Faulty Drain Pump Motor: The motor might wear out over time.
- Blocked Drainpipe: The house drain itself may be clogged.
- Kinked or Twisted Drain Hose: Restricts water flow.
- Air Lock in the Drain System: Trapped air prevents proper draining.
- Wiring Issues: Damaged wires can prevent the pump from receiving power.
- Defective Pressure Switch: This switch signals when to start the drain cycle.
- Control Board Malfunction: (Less common) The main control board could be sending incorrect signals.
Symptoms Checklist
If you suspect a drain pump problem, look for these signs:
- Washer doesn’t drain water after the wash cycle.
- Washer makes unusual noises during the drain cycle (grinding, humming).
- Error code related to draining is displayed on the control panel.
- Water drains very slowly.
- Standing water remains in the drum after the cycle is complete.
How to Fix Kenmore Washer Drain Pump Problem Step-by-Step Guide
Follow these steps to troubleshoot and potentially fix your Kenmore washer’s drain pump problem:
- Unplug the Washer: Safety first! Disconnect the power cord from the outlet.
- Locate the Drain Hose: It’s usually at the back of the washer.
- Check the Drain Hose for Kinks: Straighten any kinks or twists.
- Detach the Drain Hose: Carefully remove the hose from the drainpipe. Have a bucket ready to catch any water.
- Inspect the Drain Hose: Look for clogs. You can use a straightened coat hanger or a hose to flush it out.
- Check the Drainpipe: Make sure the house drain isn’t clogged.
- Access the Drain Pump: This usually requires removing an access panel (often at the front or back of the washer, near the bottom). Consult your owner’s manual.
- Inspect the Drain Pump Area: Look for any visible obstructions.
- Remove Obstructions from the Drain Pump: Small objects like coins or lint can be removed by hand or with pliers.
- Check the Pump Impeller: Try to rotate the pump impeller (the fan-like part inside the pump). If it’s stuck, try gently freeing it.
- Check the Wiring: Look for any loose or damaged wires connected to the drain pump. (More advanced, proceed with caution).
- Reassemble and Test: Put everything back together, plug in the washer, and run a short drain/spin cycle.
- Listen for Noises: Pay attention to any unusual sounds from the pump during the drain cycle.
- Check for Error Codes: See if the error code is gone.
- Run a Test Cycle: Run a full cycle to ensure the issue is resolved.
Fix the Issue Without Buying Parts
Before considering replacement, try these free methods:
- Reset the Washer: Unplug the washer for 1-2 minutes, then plug it back in. This can sometimes clear error codes.
- Clean the Drain Pump Filter (if applicable): Some Kenmore models have a filter near the drain pump. Clean it regularly.
- Check for Air Locks: Raise and lower the drain hose while running the drain cycle to dislodge any trapped air.
- Inspect all Hoses: Check for kinks, cracks, or leaks.
- Level the Washer: An unlevel washer can sometimes cause drainage issues.
When Replacement Might Be Necessary
If you’ve tried all the troubleshooting steps and the pump still isn’t working, replacement may be necessary. A new drain pump can cost between $50 and $150 USD, depending on the model. Commonly failing parts include the pump motor itself, the impeller, or the pump housing if it’s cracked.
Safety Warning
- Always unplug the washer before performing any maintenance or repairs.
- Be careful when handling water to avoid slips and falls.
- Do not attempt repairs if you are not comfortable working with electrical appliances. Call a professional.
- If the washer is leaking, turn off the water supply to prevent further damage.
Tools You May Need
- Screwdrivers (Phillips and flathead)
- Pliers
- Bucket
- Towels
- Flashlight
- Gloves
FAQ
Here are some frequently asked questions:
-
Q: Why is my washer making a loud buzzing noise when it tries to drain?
A: This often indicates that the drain pump is blocked by an object or the motor is failing. -
Q: How do I know if my drain pump is completely broken?
A: If the washer doesn’t drain at all, and you’ve ruled out clogs, the pump is likely broken. -
Q: Can I use a universal drain pump for my Kenmore washer?
A: It’s best to use a replacement pump specifically designed for your Kenmore model to ensure proper fit and function. -
Q: How often should I clean my drain pump filter?
A: Ideally, clean the filter every 2-3 months, or more often if you wash heavily soiled clothes.
Conclusion
A Kenmore washer drain pump problem can be a nuisance, but many times it’s a simple fix. By following these troubleshooting steps, you can often resolve the issue yourself and save money on repair costs. If you’re not comfortable performing these steps, or if the problem persists, don’t hesitate to call a qualified appliance technician.
Youtube Video:
Quick Wiring Specifications & Terminal Guide
| Component / Circuit | Standard Wire Gauge | Recommended Protection |
|---|---|---|
| Control & Trigger Signals | 18 – 20 AWG | 5A – 7.5A Inline Fuse |
| Standard Auxiliary Load | 14 – 16 AWG | 15A – 20A Circuit Breaker |
| Main Power Feed / Supply | 10 – 12 AWG | 30A – 40A Heavy-Duty Relay |
Images References
Looking for more diagnostic guides? Explore our complete Washing Machine Problems 1 section for step-by-step troubleshooting solutions.
