Introduction
Discovering that your Kenmore washer doesn’t drain properly can be a frustrating experience. No one wants to deal with soggy clothes and standing water. This problem often arises at the end of a wash cycle, leaving your laundry sitting in a tub full of water. Addressing this issue promptly is important, as it can lead to mold growth, unpleasant odors, and potential damage to your machine and laundry room floor. Don’t panic! Many drainage issues are easily resolved with a few simple troubleshooting steps.
💡 Technical Key Takeaways:
- Core Focus: Diagnostic schematic and terminal connection layout for Kenmore Washer Does Not Drain.
- Target Scope: Field technicians, automotive DIYers, and residential/commercial electricians.
- Safety Rule: Always disconnect the primary power source/battery terminal and verify zero voltage with a multimeter before touching wires.
Common Causes of kenmore washer does not drain
Several factors can contribute to a Kenmore washer refusing to drain. Here are some common culprits:
- Clogged Drain Hose: This is the most frequent cause. Lint, debris, and small objects can accumulate inside the drain hose, restricting water flow.
- Blocked Drain Pump Filter: Many Kenmore washers have a filter to catch larger debris before it reaches the drain pump. A clogged filter can prevent the pump from working correctly.
- Kinked or Obstructed Drain Hose: A simple kink or bend in the drain hose can restrict water flow. Make sure it is free from any obstructions.
- Faulty Drain Pump: If the drain pump is defective, it may not be able to effectively pump water out of the washer.
- Clogged House Drain: The problem might not be your washer at all! A clogged house drain can prevent the washer from draining properly.
- Lid Switch Problems: Some washers won’t drain if the lid switch is malfunctioning, as it may not signal the washer to proceed with the drain cycle.
- Air Lock in Drain Hose: Sometimes, air can get trapped in the drain hose, creating an air lock that prevents the water from flowing freely.
- Defective Control Board: In rare cases, a malfunctioning control board can prevent the washer from initiating the drain cycle.
Symptoms Checklist
Use this checklist to accurately identify if your Kenmore washer is experiencing a drainage issue:
- Washer cycle completes, but the drum is full of water.
- The washer makes a humming or buzzing sound but doesn’t drain.
- Water drains very slowly from the washer.
- An error code related to draining appears on the washer’s display (if equipped).
- The drain hose vibrates or shakes excessively during the drain cycle.
How to Fix kenmore washer does not drain Step-by-Step Guide
- Unplug the Washer: Always disconnect the washer from the power outlet before starting any troubleshooting.
- Check the Drain Hose: Locate the drain hose at the back of the washer and inspect it for kinks, bends, or obstructions. Straighten any kinks and make sure the hose isn’t crushed.
- Detach the Drain Hose: Disconnect the drain hose from both the washer and the drainpipe or standpipe.
- Flush the Drain Hose: Use a garden hose or sink faucet to flush the drain hose with water. This will help dislodge any debris that may be blocking the flow.
- Check the Drainpipe/Standpipe: Ensure the drainpipe or standpipe is clear. You can use a plumber’s snake or a wet/dry vacuum to remove any clogs.
- Locate the Drain Pump Filter: Consult your washer’s user manual to find the location of the drain pump filter. It’s usually located at the front or bottom of the machine, behind a small access panel.
- Clean the Drain Pump Filter: Open the access panel and carefully remove the drain pump filter. Clean it thoroughly under running water, removing any lint, hair, or debris.
- Reinstall the Drain Pump Filter: Reattach the cleaned drain pump filter securely back into its housing.
- Reconnect the Drain Hose: Reconnect the drain hose to both the washer and the drainpipe or standpipe, ensuring it is securely attached.
- Check the Lid Switch: Manually depress the lid switch (usually located near the lid hinge) to see if it clicks properly. If it doesn’t click or feels loose, it might be faulty.
- Run a Test Cycle: Plug the washer back in and run a short drain and spin cycle to see if the problem is resolved.
- Listen to the Drain Pump: While the washer is running the drain cycle, listen closely to the drain pump. If you hear a humming or buzzing sound but no water is draining, the pump might be blocked or defective.
- Check for Air Lock: Make sure that the drain hose is not pushed too far into the drainpipe. This can cause an air lock and prevent proper drainage.
Fix the Issue Without Buying Parts
Before considering replacement parts, try these cost-free methods:
- Washer Reset: Unplug your washer for 1-2 minutes. Plug it back in and run a drain/spin cycle. This can sometimes reset the internal computer.
- Hose Repositioning: Check that the drain hose has enough slack and isn’t sharply bent.
- Regular Cleaning: Run a washer cleaning cycle with vinegar or a washing machine cleaner regularly to prevent buildup.
- Drain Screen Inspection: Frequently check and clear the drain screen inside the washing machine drum.
When Replacement Might Be Necessary
If the above steps don’t resolve the issue, a part replacement might be needed. The drain pump is a common culprit, costing between $50 and $150. The lid switch can also fail, with replacements ranging from $20 to $50. In rare cases, a faulty control board (costing $100 – $300) may need replacing, but this should be diagnosed by a qualified technician. For more related activities, check out our Ge Washer Will Not Drain Water.
Safety Warning
- Always unplug the washer before performing any repairs.
- Be careful when handling water, as it can create a slip hazard.
- Avoid touching any electrical components inside the washer.
- If you are not comfortable performing any of these repairs, consult a qualified appliance technician.
Tools You May Need
- Screwdrivers (Phillips and flathead)
- Pliers
- Bucket or container to catch water
- Towel or cloths
- Plumber’s snake (optional)
- Wet/dry vacuum (optional)
FAQ
Q: Why is my washer making a humming noise but not draining?
A: This usually indicates a problem with the drain pump, either a blockage or a failing motor. Check and clean the drain pump filter first.
Q: How often should I clean my washer’s drain pump filter?
A: It’s recommended to clean the drain pump filter every 2-3 months, or more frequently if you wash heavily soiled items.
Q: Can a clogged drain cause other problems with my washer?
A: Yes, a clogged drain can put extra strain on the drain pump, potentially leading to premature failure. It can also cause mold and mildew growth.
Q: What should I do if I can’t find the drain pump filter on my Kenmore washer?
A: Consult your washer’s user manual for the exact location of the drain pump filter. If you can’t find it, search online for your specific model number.
Conclusion
Don’t let a washer that won’t drain ruin your day! By following these simple troubleshooting steps, you can often resolve the issue yourself without the expense of calling a technician. Start with the easiest solutions, like checking the drain hose and filter. If the problem persists, consider the possibility of a faulty pump or lid switch. If you’re uncomfortable with any of these steps, it’s always best to call a qualified appliance repair technician.
Youtube Video:
Quick Wiring Specifications & Terminal Guide
| Component / Circuit | Standard Wire Gauge | Recommended Protection |
|---|---|---|
| Control & Trigger Signals | 18 – 20 AWG | 5A – 7.5A Inline Fuse |
| Standard Auxiliary Load | 14 – 16 AWG | 15A – 20A Circuit Breaker |
| Main Power Feed / Supply | 10 – 12 AWG | 30A – 40A Heavy-Duty Relay |
Images References
Looking for more diagnostic guides? Explore our complete Washing Machine Problems 3 section for step-by-step troubleshooting solutions.
