Kenmore Side By Side Refrigerator Freezer Not Working


Kenmore Side By Side Refrigerator Freezer Not Working

Introduction

A refrigerator that isn’t cooling properly, especially the freezer section in a Kenmore side-by-side model, can be a homeowner’s nightmare. Food spoilage can lead to wasted money and potential health hazards. This issue often arises unexpectedly, causing immediate concern. Addressing this problem promptly is essential to prevent further food loss and potentially costly repairs. This guide will walk you through common causes and troubleshooting steps you can take before calling a professional.

💡 Technical Key Takeaways:

  • Core Focus: Diagnostic schematic and terminal connection layout for Kenmore Side By Side Refrigerator Freezer Not Working.
  • Target Scope: Field technicians, automotive DIYers, and residential/commercial electricians.
  • Safety Rule: Always disconnect the primary power source/battery terminal and verify zero voltage with a multimeter before touching wires.

Common Causes of kenmore side by side refrigerator freezer not working

Here are some frequent reasons why your Kenmore side-by-side refrigerator freezer might not be working:

  • Dirty Condenser Coils: Dust and debris accumulate on the coils, hindering heat release.
  • Blocked Vents: Air vents connecting the freezer and refrigerator can become obstructed, disrupting airflow.
  • Faulty Door Seals: Worn or damaged door seals allow warm air to enter, affecting cooling efficiency.
  • Overloaded Refrigerator/Freezer: Overpacking restricts airflow and can impact cooling.
  • Incorrect Temperature Settings: Check if the thermostat is set too warm.
  • Defrost System Issues: A malfunctioning defrost system can lead to ice buildup, blocking airflow.
  • Failed Start Relay: A failed start relay can prevent the compressor from starting.
  • Compressor Problems: The compressor is the heart of the cooling system, and failure will stop cooling.
  • Fan Motor Issues: The condenser and evaporator fan motors move air around coils and the refrigerator; failure will limit cooling.
  • Control board problems: The control board may be damaged.

Symptoms Checklist

Use this checklist to accurately identify the problem:

  • Freezer temperature is above 32F (0C).
  • Refrigerator temperature is too warm.
  • Ice cream is melting in the freezer.
  • Food is spoiling faster than usual.
  • You hear unusual noises from the refrigerator.
  • Ice buildup is visible in the freezer.
  • The refrigerator runs constantly without shutting off.
  • The back panel of the freezer or refrigerator is very cold or frosted over.

How to Fix kenmore side by side refrigerator freezer not working Step-by-Step Guide

Follow these steps to troubleshoot your Kenmore side-by-side refrigerator freezer:

  1. Check the Power Supply: Ensure the refrigerator is plugged in securely and the outlet is working by testing it with another appliance.
  2. Inspect the Temperature Settings: Verify that the temperature settings for both the freezer and refrigerator are correctly set. A setting too high can cause cooling issues. Optimal settings are usually around 0F (-18C) for the freezer and 37F (3C) for the refrigerator.
  3. Clean the Condenser Coils: Locate the condenser coils (usually on the back or bottom of the refrigerator) and unplug the unit. Use a vacuum cleaner or a brush to remove dust and debris. Plug the unit back in after cleaning.
  4. Check and Clear Air Vents: Locate the air vents inside the freezer and refrigerator, and ensure they are not blocked by food items. Rearrange items to allow proper airflow.
  5. Inspect the Door Seals: Examine the door seals (gaskets) for any signs of damage or wear. Clean the seals with warm, soapy water to remove any buildup. To test the seal, place a dollar bill between the door and the refrigerator. If you can easily pull it out, the seal needs attention.
  6. Defrost the Refrigerator Manually: If you suspect ice buildup is the issue, manually defrost the refrigerator. Unplug the unit, remove all food, and leave the doors open for several hours (or overnight) to allow the ice to melt. Place towels to catch water.
  7. Check the Defrost Drain: After defrosting, check the defrost drain (usually located at the back of the freezer) for clogs. Use a small brush or pipe cleaner to clear any blockages.
  8. Listen for the Compressor: The compressor is located at the back of the refrigerator. Listen to see if it is running. If it’s not, it may be a sign of a more serious issue.
  9. Check the Fan Motors: There are two fan motors the condenser fan (near the compressor) and the evaporator fan (inside the freezer). Ensure both are running. If either is not running, it could be a sign of a faulty motor.
  10. Check the Start Relay: A faulty start relay can prevent the compressor from starting. This relay is usually on the side of the compressor.
  11. Avoid Overloading: Make sure you are not overloading the fridge or freezer with too much food, as this can prevent proper airflow.

Fix the Issue Without Buying Parts

Here are some free methods to try before considering part replacements:

  • Reset the Refrigerator: Unplug the refrigerator for 10-15 minutes, then plug it back in. This can sometimes reset the system and resolve minor issues.
  • Thorough Cleaning: Clean the interior and exterior of the refrigerator, including the door seals and condenser coils.
  • Recalibration: If your model has a digital display, check the user manual for instructions on recalibrating the temperature settings.
  • Inspection Tips: Regularly inspect the interior for ice buildup and the exterior for dust accumulation.
  • Maintenance Basics: Schedule regular cleaning and defrosting to prevent future problems.

When Replacement Might Be Necessary

If the above steps do not resolve the issue, component failure may be the cause. Parts that often fail include the defrost heater, defrost timer, start relay, and compressor. Replacing these parts can range from $50 to $500+, depending on the part and if you hire a professional. If the compressor is bad, consider whether it’s worth repairing an older fridge versus purchasing a newer, more energy-efficient model. For more related activities, check out our No Frost Fridge Leaking Water.

Safety Warning

  • Always unplug the refrigerator before performing any maintenance or repairs.
  • Avoid working on electrical components if you are not comfortable or experienced.
  • Be careful when handling sharp tools or cleaning agents.
  • Keep the floor dry to prevent slips and falls.
  • If you are unsure about any step, consult a qualified technician.

Tools You May Need

Here’s a list of simple tools that might be helpful:

  • Screwdrivers (Phillips and flathead)
  • Vacuum cleaner with brush attachment
  • Soft brush or duster
  • Warm water and mild dish soap
  • Towels
  • Pipe cleaner or small brush

FAQ

Here are some common questions about refrigerator problems:

  • Q: Why is my freezer cold, but my refrigerator is not? A: This is often caused by blocked air vents between the freezer and refrigerator. Clear any obstructions.
  • Q: How often should I clean the condenser coils? A: Aim to clean them every 6 months to a year for optimal performance.
  • Q: What temperature should my refrigerator and freezer be set to? A: 37F (3C) for the refrigerator and 0F (-18C) for the freezer are generally recommended.
  • Q: Why is my refrigerator running constantly? A: This can be due to dirty condenser coils, a faulty door seal, or an overloaded refrigerator.

Conclusion

Troubleshooting a “kenmore side by side refrigerator freezer not working” issue can seem daunting, but with these steps, you can often diagnose and fix the problem yourself. Remember to take your time, follow the instructions carefully, and prioritize safety. Before calling a technician, try these DIY solutions you might save yourself time and money. If the problem persists, it’s best to consult a qualified appliance repair professional.

Youtube Video:


Quick Wiring Specifications & Terminal Guide

Component / Circuit Standard Wire Gauge Recommended Protection
Control & Trigger Signals 18 – 20 AWG 5A – 7.5A Inline Fuse
Standard Auxiliary Load 14 – 16 AWG 15A – 20A Circuit Breaker
Main Power Feed / Supply 10 – 12 AWG 30A – 40A Heavy-Duty Relay

Images References


Images References, Refrigerator Problems 4

Looking for more diagnostic guides? Explore our complete Refrigerator Problems 4 section for step-by-step troubleshooting solutions.

📚 Related Articles

Scroll to Top