Kenmore Side By Side Not Making Ice


Kenmore Side By Side Not Making Ice

Introduction

A refrigerator’s ice maker is a convenient appliance, especially during warmer months. When your Kenmore side-by-side refrigerator stops making ice, it can be a real inconvenience. You’re suddenly facing a lack of readily available ice for drinks, forcing you to buy ice from the store. Fixing this issue promptly is important to avoid the hassle and potential food spoilage if the refrigerator temperature rises due to increased door opening for ice.

💡 Technical Key Takeaways:

  • Core Focus: Diagnostic schematic and terminal connection layout for Kenmore Side By Side Not Making Ice.
  • Target Scope: Field technicians, automotive DIYers, and residential/commercial electricians.
  • Safety Rule: Always disconnect the primary power source/battery terminal and verify zero voltage with a multimeter before touching wires.

Common Causes of Kenmore Side by Side Not Making Ice

Several factors can cause a Kenmore side-by-side refrigerator to stop producing ice:

  • Water Supply Issues: The refrigerator needs a consistent water supply to make ice. A kinked, frozen, or disconnected water line is a frequent culprit.
  • Water Filter: A clogged water filter restricts water flow to the ice maker.
  • Freezer Temperature: If the freezer isn’t cold enough (ideally 0-5F or -18 to -15C), the ice maker won’t function correctly.
  • Ice Maker Jam: Ice cubes can sometimes jam the ice maker mechanism, preventing it from producing more ice.
  • Ice Maker Switch: The ice maker has an on/off switch or lever. It might have been accidentally turned off.
  • Fill Tube Frozen: The fill tube, which carries water to the ice maker, can freeze.
  • Faulty Water Inlet Valve: This valve controls the water flow to the ice maker. If it fails, water won’t reach the ice maker.
  • Defective Ice Maker Module: This is the main control unit of the ice maker. If it fails, the ice maker won’t work.
  • Door Switch Problems: A faulty door switch can prevent the ice maker from operating.

Symptoms Checklist

Use this checklist to identify your specific issue:

  • No ice production at all.
  • Ice maker making only small or hollow cubes.
  • Ice maker producing ice very slowly.
  • Water dispenser not working.
  • Strange noises coming from the ice maker.
  • Ice cubes clumped together.

How to Fix Kenmore Side by Side Not Making Ice Step-by-Step Guide

Follow these steps to troubleshoot your ice maker:

  1. Check the Ice Maker Switch: Ensure the ice maker is turned “on”. Look for a switch or lever inside the freezer, near the ice maker.
  2. Verify Freezer Temperature: Use a thermometer to ensure the freezer temperature is between 0-5F (-18 to -15C). Adjust the temperature control if needed. Give it 24 hours to stabilize.
  3. Inspect the Water Line: Check the water line behind the refrigerator for kinks, bends, or damage. Ensure it’s properly connected to the water supply.
  4. Check the Water Supply Valve: Make sure the water supply valve (usually located under the sink or behind the refrigerator) is fully open.
  5. Replace the Water Filter: Replace the water filter every 6 months or as recommended by the manufacturer. A clogged filter restricts water flow.
  6. Check for Ice Maker Jam: Look for ice jams in the ice maker tray. Use a plastic utensil (never metal) to carefully remove any obstructions.
  7. Thaw a Frozen Fill Tube: If you suspect a frozen fill tube, unplug the refrigerator and let it thaw for a few hours. You can also use a hairdryer (on a low setting) to gently warm the tube.
  8. Listen for the Water Inlet Valve: When the ice maker cycles (every few hours), listen for a buzzing sound from the water inlet valve. If you don’t hear anything, it might be faulty.
  9. Reset the Ice Maker: Some Kenmore ice makers have a reset button. Consult your owner’s manual for its location and how to use it. Typically, holding the button for a few seconds will initiate a reset.
  10. Inspect the Ejector Arm: Make sure the ejector arm (the plastic arm that pushes ice out of the mold) moves freely. If it’s stuck, gently try to loosen it.
  11. Clean the Ice Maker: Periodically clean the ice maker with a solution of baking soda and water. This helps remove mineral deposits and buildup.
  12. Check Door Seal: Make sure door seals are properly sealing the freezer door. Warm freezer temps prevent ice.

Fix the Issue Without Buying Parts

Many ice maker problems can be resolved without replacing any parts:

  • Refrigerator Reset: Unplug your refrigerator for 5-10 minutes, then plug it back in. This can reset the ice maker’s controls.
  • Cleaning: Regularly clean the ice maker and surrounding area to prevent jams and buildup.
  • Defrosting: Manually defrosting the freezer can clear ice buildup and resolve fill tube freezing.
  • Inspection: Carefully inspect the water line for any obvious signs of damage or kinks.
  • Maintenance: Replace the water filter regularly and keep the freezer clean to prevent future problems.

When Replacement Might Be Necessary

If you’ve tried all the troubleshooting steps and the ice maker still isn’t working, a part replacement might be necessary. Common parts that fail include:

  • Water Inlet Valve: $30-$80 USD
  • Ice Maker Module: $50-$150 USD
  • Water Filter Housing: $20-$50 USD

Safety Warning

  • Always unplug the refrigerator before performing any repairs.
  • Avoid working on electrical components if you’re not comfortable with electrical work. Call a professional.
  • Be careful when handling water lines to avoid leaks or spills.
  • Do not use sharp objects to remove ice jams, as this can damage the ice maker.

Tools You May Need

  • Screwdrivers (Phillips and flathead)
  • Adjustable wrench
  • Pliers
  • Thermometer
  • Baking soda
  • Clean cloths
  • Plastic utensils

FAQ


Q: My ice maker is making ice, but it’s very small. What could be the problem?
A: This is often caused by low water pressure or a partially clogged water filter. Check the water supply and replace the filter if necessary.


Q: How long does it take for a new ice maker to start producing ice?
A: It typically takes 24-48 hours for a new ice maker to start producing ice.


Q: My ice tastes funny. What should I do?
A: Replace the water filter. Old water filter produce bad taste.


Q: The water dispenser isn’t working either. Could it be related to the ice maker problem?
A: Yes, if the water dispenser and ice maker aren’t working, it’s likely a water supply issue or a problem with the water inlet valve.

Conclusion

Troubleshooting a Kenmore side-by-side ice maker can seem daunting, but by following these steps, you can often resolve the issue yourself. Don’t hesitate to give these steps a try before calling a technician. You might save yourself time and money! If you’ve exhausted these options and the ice maker still isn’t working, it may be time to consult with a qualified appliance repair professional.

Youtube Video:


Quick Wiring Specifications & Terminal Guide

Component / Circuit Standard Wire Gauge Recommended Protection
Control & Trigger Signals 18 – 20 AWG 5A – 7.5A Inline Fuse
Standard Auxiliary Load 14 – 16 AWG 15A – 20A Circuit Breaker
Main Power Feed / Supply 10 – 12 AWG 30A – 40A Heavy-Duty Relay

Images References


Images References, Refrigerator Problems 4

Looking for more diagnostic guides? Explore our complete Refrigerator Problems 4 section for step-by-step troubleshooting solutions.

📚 Related Articles

Scroll to Top