Introduction
It’s frustrating when your Kenmore Elite refrigerator provides cold water but refuses to make ice, especially during hot weather or when you’re entertaining. A non-working ice maker, while the water dispenser functions, points to a specific set of potential problems. It’s important to address this issue promptly to avoid relying on inconvenient alternatives like buying ice from the store. Plus, a malfunctioning ice maker might indicate a larger problem with your refrigerator’s overall cooling system, so let’s get it fixed!
💡 Technical Key Takeaways:
- Core Focus: Diagnostic schematic and terminal connection layout for Kenmore Elite Refrigerator Not Making Ice But Water Works.
- Target Scope: Field technicians, automotive DIYers, and residential/commercial electricians.
- Safety Rule: Always disconnect the primary power source/battery terminal and verify zero voltage with a multimeter before touching wires.
Common Causes of Kenmore Elite Refrigerator Not Making Ice But Water Works
Here are some common reasons why your Kenmore Elite ice maker might be on strike, even though the water dispenser works:. For more related activities, check out our Fridge Water Line Leaking In Wall.
- Ice Maker is Turned Off: Believe it or not, this is the most common reason. There’s often a switch or setting to disable the ice maker.
- Ice Build-Up in the Ejector: Ice can accumulate and prevent the ice maker from ejecting cubes.
- Frozen Water Line: Although the water dispenser works, a separate section of the water line leading specifically to the ice maker could be frozen.
- Faulty Water Inlet Valve: This valve controls the water flow to the ice maker. It might be partially blocked or malfunctioning.
- Defective Ice Maker Module: The module controls the ice-making process. If it’s faulty, the ice maker won’t function.
- Clogged Water Filter: A clogged filter can restrict water flow to the ice maker, even if the dispenser has enough pressure.
- Low Freezer Temperature: If the freezer isn’t cold enough (ideally around 0-5F), the ice maker won’t function properly.
- Ice Level Control Arm Stuck: If your model has a feeler arm, it might be stuck in the “up” position, signaling that the ice bin is full, even if it isn’t.
Symptoms Checklist
Use this checklist to help identify the issue:
- Water dispenser works fine.
- No ice is being produced, or the ice maker is producing very little ice.
- Ice maker may or may not be making noise.
- Ice cubes, if any, may be small or oddly shaped.
- Water filter light may be illuminated (indicating a need for replacement).
- Freezer temperature feels warmer than usual.
How to Fix Kenmore Elite Refrigerator Not Making Ice But Water Works Step-by-Step Guide
Follow these steps to troubleshoot your Kenmore Elite ice maker:
- Check the Ice Maker Switch: Locate the ice maker switch (usually on the side or top of the ice maker) and ensure it’s turned “on.” Some models have a sensor arm that must be down.
- Verify the Freezer Temperature: Ensure your freezer is set to the correct temperature, ideally between 0-5F (-18 to -15C). Use a thermometer to confirm.
- Inspect the Ice Ejector: Check for any ice buildup around the ice maker’s ejector arms. If there’s ice, gently remove it. You can use a plastic utensil (not metal, to avoid damage).
- Check the Water Filter: A clogged water filter can drastically reduce water flow to the ice maker. Replace the water filter according to the manufacturer’s instructions (usually every 6 months). Refer to your owner’s manual for the correct filter type.
- Inspect the Water Line: Look for any kinks or bends in the water line behind the refrigerator. Straighten them out to ensure proper water flow.
-
Check for a Frozen Water Line: If you suspect a frozen line (even though the dispenser works), try these steps:
- Unplug the refrigerator.
- Locate the water line going to the ice maker (usually a small plastic tube).
- Use a hairdryer (on low setting) to gently warm the water line for a few minutes. Be careful not to melt the plastic.
- Plug the refrigerator back in and wait a few hours to see if the ice maker starts working.
- Listen for the Water Inlet Valve: With the refrigerator plugged in and the ice maker turned on, have someone press the ice maker fill button (usually located near the ice maker itself). You should hear a buzzing sound from the back of the refrigerator, indicating the water inlet valve is opening. If you don’t hear anything, the valve might be faulty.
- Reset the Ice Maker: Some Kenmore Elite models have a reset button on the ice maker module. Press and hold this button for a few seconds to reset the ice maker. Check your owner’s manual for specific instructions.
- Clean the Ice Bin: An overly full ice bin or one with old, stale ice can sometimes interfere with the ice maker’s operation. Empty and clean the ice bin thoroughly.
- Check the Ice Level Control Arm: If your model has a feeler arm that rises as the ice bin fills, make sure it’s moving freely. If it’s stuck in the “up” position, it might be preventing the ice maker from cycling.
Fix the Issue Without Buying Parts
Before you consider replacing any parts, try these free methods:
- Power Cycle: Unplug the refrigerator for 5-10 minutes, then plug it back in. This can sometimes reset the ice maker.
- Deep Clean: Ensure the freezer and ice maker area are free of debris and ice buildup.
- Temperature Adjustment: Fine-tune the freezer temperature slightly. A degree or two can sometimes make a difference.
- Visual Inspection: Regularly inspect the water line and ice maker components for any visible damage.
- Preventative Maintenance: Replace the water filter every 6 months, even if the light isn’t illuminated.
When Replacement Might Be Necessary
If you’ve tried all the troubleshooting steps and the ice maker still isn’t working, it might be time to consider replacing a part. Common parts that fail are the water inlet valve (estimated cost: $30-$60), the ice maker module (estimated cost: $80-$150), or the entire ice maker assembly (estimated cost: $150-$300). Before replacing anything, consult with a qualified appliance repair technician to diagnose the problem accurately. They can confirm which part is faulty and whether replacement is the best option.
Safety Warning
- Always unplug the refrigerator before attempting any repairs.
- Avoid working on the refrigerator with wet hands.
- Be careful when using a hairdryer to thaw a frozen water line. Do not overheat the plastic tubing.
- If you’re uncomfortable performing any of these steps, consult a qualified appliance repair technician.
Tools You May Need
- Screwdrivers (Phillips and flathead)
- Pliers
- Adjustable wrench
- Thermometer
- Hairdryer (optional)
- Towels
FAQ
Here are some frequently asked questions about ice maker problems:
-
Q: Why is my ice maker making small or hollow ice cubes?
A: This is usually caused by low water pressure or a partially clogged water filter. Replace the filter and check the water supply line. -
Q: How long does it take for a new ice maker to start producing ice?
A: It can take up to 24 hours for a new ice maker to produce its first batch of ice. -
Q: My ice maker is making ice, but it’s not dispensing. What’s wrong?
A: This could be a problem with the dispenser motor, the dispenser auger, or ice blockage in the dispenser chute. -
Q: Can I manually fill the ice maker with water?
A: No, manually filling the ice maker will likely damage it.
Conclusion
Troubleshooting a Kenmore Elite ice maker that’s not working can be a manageable task. By following these steps, you can often identify and resolve the issue without needing to call a technician. However, if you’ve exhausted all the troubleshooting options and the problem persists, don’t hesitate to contact a qualified appliance repair professional for assistance. Remember, safety first!
Youtube Video:
Quick Wiring Specifications & Terminal Guide
| Component / Circuit | Standard Wire Gauge | Recommended Protection |
|---|---|---|
| Control & Trigger Signals | 18 – 20 AWG | 5A – 7.5A Inline Fuse |
| Standard Auxiliary Load | 14 – 16 AWG | 15A – 20A Circuit Breaker |
| Main Power Feed / Supply | 10 – 12 AWG | 30A – 40A Heavy-Duty Relay |
Images References
Looking for more diagnostic guides? Explore our complete Refrigerator Problems 1 section for step-by-step troubleshooting solutions.
