Kenmore 80 Series Washer Won T Stop Filling


Kenmore 80 Series Washer Won T Stop Filling

Introduction

If your Kenmore 80 series washer keeps filling with water even after it should have stopped, you’ve got a problem. This means the washer isn’t sensing the correct water level and continues to fill, potentially overflowing. This isn’t just annoying; it can waste water, damage your floors, and even ruin nearby belongings. It’s important to address this issue quickly to prevent further damage and get your laundry routine back on track.

💡 Technical Key Takeaways:

  • Core Focus: Diagnostic schematic and terminal connection layout for Kenmore 80 Series Washer Won T Stop Filling.
  • Target Scope: Field technicians, automotive DIYers, and residential/commercial electricians.
  • Safety Rule: Always disconnect the primary power source/battery terminal and verify zero voltage with a multimeter before touching wires.

Common Causes of Kenmore 80 Series Washer Won’t Stop Filling

Here are some reasons your Kenmore 80 series washer might be overfilling:

  • Faulty Water Inlet Valve: This valve controls the water flow into the washer. If it’s stuck open, water will continuously flow.
  • Pressure Switch Problems: The pressure switch senses the water level. If it’s defective or the hose connected to it is blocked, it won’t signal the washer to stop filling.
  • Blocked or Kinked Pressure Hose: The hose running from the tub to the pressure switch can get blocked with lint or kinked, preventing accurate water level readings.
  • Faulty Timer or Control Board: In some cases, the timer or control board that manages the wash cycles might be malfunctioning, failing to signal the water inlet valve to close.
  • Siphon Issue: If the drain hose is too low in the standpipe (drain pipe in the wall), it can create a siphon effect, pulling water in even when the valve is closed.
  • Air Dome Obstruction: There is an air dome (air trap) in some washers that is connected to the pressure hose. If the air dome becomes clogged with debris, then the pressure switch may not detect the proper water level.

Symptoms Checklist

Here are some signs to confirm your Kenmore 80 series washer is overfilling:

  • Water continuously flows into the washer tub, even when the machine is off.
  • The water level rises above the fill line marked inside the tub.
  • Water overflows from the top of the washer.
  • You hear the sound of water filling even when the washer isn’t running a fill cycle.
  • The washer doesn’t proceed to the next cycle (washing, rinsing, spinning) because it thinks it’s still filling.

How to Fix Kenmore 80 Series Washer Won’t Stop Filling Step-by-Step Guide

Follow these steps to troubleshoot and potentially fix the problem:

  1. Unplug the Washer: Safety first! Disconnect the washer from the power outlet to prevent electric shock.
  2. Inspect the Drain Hose: Make sure the drain hose is properly inserted into the standpipe and that it’s not pushed too far down. Ideally, it should be a few inches above the bottom of the standpipe.
  3. Check for Siphoning: If the drain hose is too low, try raising it to see if that stops the continuous filling. Secure it so it doesn’t fall back down.
  4. Locate the Pressure Switch: This is usually a round, plastic component located behind the control panel or on the side of the washer. Refer to your washer’s service manual if you have trouble finding it.
  5. Inspect the Pressure Hose: Locate the small rubber hose connected to the pressure switch. Check for kinks, cracks, or loose connections.
  6. Remove and Clean the Pressure Hose: Disconnect the hose from both the pressure switch and the tub. Blow through the hose to ensure it’s clear. If you find any debris, flush it out with water.
  7. Inspect the Air Dome: Locate the air dome in the washer. It is connected to the pressure hose. Make sure it is not clogged with debris.
  8. Check the Pressure Switch Connection: Make sure the wires connected to the pressure switch are securely attached.
  9. Check the Water Inlet Valve Hoses: Locate the water inlet valve (where the hot and cold water hoses connect to the washer). Check the hoses for kinks or blockages.
  10. Clean the Water Inlet Valve Screens: Turn off the water supply to the washer. Disconnect the hoses from the water inlet valve. There should be small screens inside the valve inlets. Clean these screens with a brush or toothbrush to remove any sediment or debris.
  11. Check Water Pressure: Make sure you have adequate water pressure. Low water pressure can sometimes cause the washer to fill improperly.
  12. Reset the Washer: Some Kenmore washers have a reset procedure. Unplug the washer for 1-2 minutes, then plug it back in. This can sometimes clear minor control board glitches.
  13. Observe During Filling: Plug the washer back in and start a wash cycle. Carefully watch the water level. If the water still doesn’t stop filling at the appropriate level, proceed to the next step.

Fix the Issue Without Buying Parts

Before you start buying parts, try these free methods:

  • Reset the Washer: As mentioned above, unplugging the washer for a minute or two can sometimes resolve minor electronic glitches.
  • Cleaning: Regularly clean the pressure hose and water inlet valve screens to prevent blockages.
  • Inspection: Regularly inspect the drain hose for proper placement and to ensure it is not creating a siphoning effect. Also check the pressure hose and air dome.
  • Maintenance: Run a washer cleaning cycle monthly with a washing machine cleaner to remove buildup and prevent clogs.

When Replacement Might Be Necessary

If you’ve tried all the above steps and your Kenmore 80 series washer still won’t stop filling, the water inlet valve or pressure switch might be faulty and need replacement. Water Inlet valves can range from $30$70, while a pressure switch typically costs $20$50. It’s always best to confirm the specific part number for your washer model before ordering. If you’re not comfortable replacing these parts yourself, it’s time to call a qualified appliance repair technician. For more related activities, check out our Hoover Dynamic Next Leaking From Bottom.

Safety Warning

  • Always unplug the washer before performing any repairs.
  • Avoid standing in water while working on electrical appliances.
  • If you’re unsure about any step, consult a qualified appliance repair technician.
  • Be careful when handling tools to avoid injury.

Tools You May Need

  • Screwdrivers (Phillips and flathead)
  • Pliers
  • Adjustable wrench
  • Bucket or towels (to catch spilled water)
  • Small brush or toothbrush

FAQ


Q: Why is my washer filling slowly and then not stopping?
A: This could be due to low water pressure or partially clogged water inlet valve screens. Clean the screens first.


Q: How do I know if the pressure switch is bad?
A: If you’ve checked the hose and it’s clear, and the washer still overfills, the pressure switch is likely faulty. You may need a multimeter to test its continuity, which may require more advanced knowledge.


Q: Can I still use my washer if it overfills slightly?
A: No, it’s not recommended. Overfilling can damage the washer and your home due to the water overflow. It can also lead to inefficient washing and potential motor damage.


Q: What if I can’t find the pressure switch?
A: Consult your washer’s service manual or search online for diagrams specific to your Kenmore 80 series model. If you still can’t find it, it’s best to call a technician.

Conclusion

Troubleshooting a Kenmore 80 series washer that won’t stop filling can seem daunting, but by following these steps, you can often identify and fix the problem yourself. Remember to prioritize safety and take your time. If you’re uncomfortable with any of these steps, don’t hesitate to contact a qualified appliance repair technician. Good luck!

Youtube Video:


Quick Wiring Specifications & Terminal Guide

Component / Circuit Standard Wire Gauge Recommended Protection
Control & Trigger Signals 18 – 20 AWG 5A – 7.5A Inline Fuse
Standard Auxiliary Load 14 – 16 AWG 15A – 20A Circuit Breaker
Main Power Feed / Supply 10 – 12 AWG 30A – 40A Heavy-Duty Relay

Images References


Images References, Washing Machine Problems 3

Looking for more diagnostic guides? Explore our complete Washing Machine Problems 3 section for step-by-step troubleshooting solutions.

📚 Related Articles

Scroll to Top