Kenmore 70 Series Washer Will Not Drain


Kenmore 70 Series Washer Will Not Drain

Introduction

Is your Kenmore 70 series washer refusing to drain? This is a common problem that can leave you with a tub full of water and wet laundry. A washer that won’t drain can be frustrating, inconvenient, and even lead to mold or mildew if left unattended for too long. Addressing this issue promptly is important to prevent further damage and get your laundry routine back on track. This guide will walk you through the steps to diagnose and fix the problem yourself, saving you time and money.

💡 Technical Key Takeaways:

  • Core Focus: Diagnostic schematic and terminal connection layout for Kenmore 70 Series Washer Will Not Drain.
  • Target Scope: Field technicians, automotive DIYers, and residential/commercial electricians.
  • Safety Rule: Always disconnect the primary power source/battery terminal and verify zero voltage with a multimeter before touching wires.

Common Causes of Kenmore 70 Series Washer Won’t Drain

Several factors can cause a Kenmore 70 series washer to not drain properly. Here are some of the most common culprits:. For more related activities, check out our Hoover Dynamic Next Leaking From Bottom.

  • Clogged Drain Hose: The drain hose can become blocked with lint, small objects, or soap buildup.
  • Clogged Drain Pump Filter: Many washers have a filter to catch debris before it reaches the drain pump. This filter can become clogged.
  • Faulty Drain Pump: The drain pump is responsible for pushing the water out of the washer. If it’s malfunctioning, it won’t drain the water.
  • Blocked Drainpipe: The drainpipe where the washer empties might be clogged.
  • Kinked or Twisted Drain Hose: A kink or twist in the drain hose can restrict water flow.
  • Lid Switch Issues: Some washers won’t drain if the lid switch isn’t working properly, as this signals to the machine that the lid is open.
  • Drive belt: Over time, this can wear out.
  • Air Lock in the Drain Hose: Trapped air can prevent the water from flowing freely.

Symptoms Checklist

Here are some indicators that can help you pinpoint the issue:

  • The washer completes the wash cycle but the tub is still full of water.
  • The washer makes a humming or buzzing noise during the drain cycle, but no water is being pumped out.
  • The washer stops mid-cycle and displays an error code related to draining (check your owner’s manual).
  • Water drains very slowly or in small spurts.
  • You find small objects or lint in the drain hose or filter.

How to Fix Kenmore 70 Series Washer Won’t Drain Step-by-Step Guide

Follow these steps to troubleshoot and fix your Kenmore 70 series washer:

  1. Unplug the Washer: For safety, always disconnect the power before working on any appliance.
  2. Check the Drain Hose: Inspect the drain hose for kinks, twists, or blockages. Straighten any kinks and ensure the hose isn’t crushed.
  3. Disconnect the Drain Hose: Carefully detach the drain hose from the drainpipe. Be prepared for some water to spill out.
  4. Inspect the Drainpipe: Check the drainpipe for any visible clogs. You can use a plumber’s snake or a bent wire to clear any obstructions.
  5. Clean the Drain Hose: Flush the drain hose with water to remove any lint or debris. You can use a garden hose for this.
  6. Locate the Drain Pump Filter: Consult your owner’s manual to find the location of the drain pump filter. It’s usually located at the front or back of the washer, near the bottom.
  7. Clean the Drain Pump Filter: Carefully remove the drain pump filter and clean it thoroughly. Remove any lint, hair, or small objects.
  8. Check the Drain Pump: With the filter removed, inspect the drain pump impeller (the fan-like blades inside). Make sure it’s not blocked by anything and can spin freely.
  9. Reassemble the Drain Pump Filter: Carefully reattach the drain pump filter, ensuring it’s securely in place.
  10. Reconnect the Drain Hose: Reconnect the drain hose to the drainpipe, making sure it’s properly secured.
  11. Check the Lid Switch: Ensure that the lid switch is functioning correctly. You can test this by manually pressing the switch while the washer is plugged in (be careful!). If the washer starts draining, the switch might be the problem.
  12. Run a Test Cycle: Plug the washer back in and run a short spin cycle to see if it drains properly.
  13. Check the drive belt: Make sure the belt is attached and in good condition.

Fix the Issue Without Buying Parts

Before considering replacement parts, try these free methods:

  • Reset the Washer: Unplug the washer for 1-2 minutes, then plug it back in. This can sometimes reset the machine’s computer and resolve minor issues.
  • Deep Cleaning: Run an empty wash cycle with a washer cleaner or a mixture of vinegar and baking soda to remove buildup and potential blockages.
  • Inspect the Area: Do a thorough visual inspection of all hoses and connections for any signs of damage or wear.

When Replacement Might Be Necessary

If you’ve tried all the troubleshooting steps and your washer still won’t drain, you might need to replace a part. The drain pump is the most common culprit. Drain pumps usually cost between $50 and $150 USD. Consider replacing the lid switch if it’s faulty.

Safety Warning

  • Always unplug the washer from the power outlet before performing any repairs.
  • Be careful when handling water, as it can create slippery conditions.
  • Avoid touching any electrical components while the washer is plugged in.
  • Consult a qualified technician if you are unsure about any of the repair steps.

Tools You May Need

  • Screwdrivers (Phillips and flathead)
  • Pliers
  • Bucket or container to catch water
  • Plumber’s snake or bent wire
  • Gloves
  • Wrench

FAQ

Here are some frequently asked questions about washer draining issues:

  • Q: Why is my washer making a humming noise but not draining? A: This usually indicates a problem with the drain pump, either a blockage or a failing motor. Clean the drain pump filter and check the impeller.
  • Q: How do I know if my drain pump is bad? A: If the pump makes unusual noises, doesn’t pump water at all, or trips the circuit breaker, it’s likely faulty.
  • Q: Can I use a regular hose to replace the drain hose? A: No, you should only use a drain hose specifically designed for washing machines.
  • Q: How often should I clean the drain pump filter? A: It’s recommended to clean the drain pump filter every 3-6 months, depending on how frequently you use your washer.

Conclusion

Troubleshooting a Kenmore 70 series washer that won’t drain can seem daunting, but by following these steps, you can often resolve the issue yourself. Start with the simple solutions like checking the hoses and filter before moving on to more complex repairs. If you’ve exhausted all the troubleshooting options and your washer still won’t drain, it might be time to call a qualified appliance repair technician. But hopefully, this guide has empowered you to tackle the problem and get your laundry routine back on track!

Youtube Video:


Quick Wiring Specifications & Terminal Guide

Component / Circuit Standard Wire Gauge Recommended Protection
Control & Trigger Signals 18 – 20 AWG 5A – 7.5A Inline Fuse
Standard Auxiliary Load 14 – 16 AWG 15A – 20A Circuit Breaker
Main Power Feed / Supply 10 – 12 AWG 30A – 40A Heavy-Duty Relay

Images References


Images References, Washing Machine Problems 3

Looking for more diagnostic guides? Explore our complete Washing Machine Problems 3 section for step-by-step troubleshooting solutions.

📚 Related Articles

Scroll to Top