Introduction
A washing machine that won’t drain is a common and frustrating problem. Imagine pulling out soaking wet clothes after thinking your laundry is done! If your Kenmore 70 series washer is not draining properly, it can lead to mildew, ruined clothes, and a real headache. It’s important to address this problem quickly to prevent further damage to your machine and your laundry.
💡 Technical Key Takeaways:
- Core Focus: Diagnostic schematic and terminal connection layout for Kenmore 70 Series Washer Not Draining.
- Target Scope: Field technicians, automotive DIYers, and residential/commercial electricians.
- Safety Rule: Always disconnect the primary power source/battery terminal and verify zero voltage with a multimeter before touching wires.
Common Causes of Kenmore 70 Series Washer Not Draining
Several things can cause your Kenmore 70 series washer to stop draining. Here are some of the most common culprits:. For more related activities, check out our Ge Washer Keeps Stopping Mid Cycle.
- Clogged Drain Hose: This is the most frequent cause. Lint, socks, or other small items can block the hose that carries the water away.
- Blocked Drain Pump: The drain pump is responsible for pushing the water out. If it’s clogged with debris, it won’t work.
- Kinked or Twisted Drain Hose: A simple kink can restrict water flow.
- Faulty Lid Switch: Some washers won’t drain if the lid switch is malfunctioning and not sensing that the lid is closed.
- Broken or Worn-Out Drive Belt: In some older models, a worn drive belt can affect the pump’s ability to function.
- Clogged Filter (if applicable): Some Kenmore 70 series models have a filter that can become clogged.
- Drain Pipe Clog: Sometimes, the problem isn’t the washer at all, but the drain pipe in your wall.
- Air Lock in Drain Hose: An air bubble trapped in the drain hose can prevent proper draining.
Symptoms Checklist
Here are some signs that your Kenmore 70 series washer is not draining correctly:
- Water remains in the drum after the wash cycle is complete.
- The washer makes unusual noises during the drain cycle.
- The drain cycle takes much longer than usual.
- The washer stops mid-cycle and displays an error code (though older models may not have codes).
- Clothes are excessively wet after the spin cycle.
How to Fix Kenmore 70 Series Washer Not Draining Step-by-Step Guide
Follow these steps to troubleshoot and fix your Kenmore 70 series washer:
- Unplug the Washer: This is the most important safety precaution! Always disconnect the power before working on any appliance.
- Inspect the Drain Hose: Locate the drain hose at the back of the washer. Check for any kinks, twists, or visible blockages. Straighten any kinks and ensure the hose isn’t crushed.
- Detach the Drain Hose: Carefully detach the drain hose from the drainpipe (usually in the wall). Have a bucket ready to catch any remaining water.
- Check for Clogs in the Drain Hose: Hold the drain hose up and try flushing it with water from a garden hose or faucet. If the water doesn’t flow freely, there’s a clog.
- Remove the Clog: Use a straightened coat hanger or a plumbing snake to dislodge the clog. Be gentle to avoid damaging the hose.
- Inspect the Drainpipe: While the drain hose is detached, check the drainpipe in the wall for clogs. A plumber’s snake can be used here as well.
- Locate the Drain Pump: The drain pump is usually located at the bottom of the washer, behind an access panel. Consult your washer’s manual (if you have it) for the exact location.
- Access the Drain Pump: Remove the access panel using a screwdriver.
- Check the Drain Pump Filter: Some models have a small filter near the drain pump. Clean out any lint or debris you find there.
- Inspect the Drain Pump Impeller: Carefully inspect the drain pump impeller (the little fan inside the pump) for obstructions. Remove any visible objects like coins or buttons. You may need pliers to remove some items.
- Check Lid Switch With the washer unplugged, carefully locate the lid switch and try pressing it manually. Sometimes, this switch can become stuck.
- Reassemble and Test: Reattach the drain hose to the drainpipe, replace the access panel, and plug the washer back in. Run a short test cycle to see if the washer now drains properly.
Fix the Issue Without Buying Parts
Sometimes, a simple fix can resolve the draining issue without needing to replace any parts:
- Reset the Washer: Unplug the washer for 1-2 minutes, then plug it back in. This can sometimes reset the electronic controls.
- Hot Water Flush: Run an empty wash cycle with hot water and a cup of vinegar. This can help dissolve minor clogs.
- Check for Air Lock: Make sure the drain hose is not inserted too far into the drainpipe. It should only go in a few inches to allow air to escape.
- Regular Maintenance: Run a washer cleaner cycle monthly to prevent lint and debris buildup.
When Replacement Might Be Necessary
If you’ve tried all the troubleshooting steps and your Kenmore 70 series washer is still not draining, the drain pump itself might be faulty. Replacing the drain pump typically costs between $50 and $150, including the part and labor if you hire a technician. Other parts that sometimes fail and require replacement include the lid switch and the drive belt, but these are less common causes of draining issues.
Safety Warning
- Always unplug the washer before performing any repairs.
- Be careful when handling water and electrical components.
- Wear gloves to protect your hands from dirt and grime.
- Clean up any spills immediately to prevent slips and falls.
Tools You May Need
- Screwdrivers (Phillips and flathead)
- Pliers
- Bucket
- Plumbing snake or straightened coat hanger
- Gloves
- Flashlight
FAQ
- Q: Why is my washer making a loud buzzing noise when it tries to drain? A: This often indicates that the drain pump is blocked or faulty. Check for obstructions and consider replacing the pump if necessary.
- Q: Can I use Drano to unclog my washing machine drain? A: No, Drano and other chemical drain cleaners can damage your washer’s components. It’s best to use mechanical methods (plumbing snake) or hot water flushes.
- Q: How often should I clean my washing machine’s drain hose? A: It’s a good idea to inspect and clean the drain hose at least once a year, or more often if you notice draining problems.
- Q: My washer drains slowly, but it eventually drains completely. What could be the problem? A: A partially clogged drain hose or drain pump is the most likely cause. Follow the steps above to check for obstructions.
Conclusion
Troubleshooting a Kenmore 70 series washer that’s not draining can seem daunting, but by following these steps, you can often identify and fix the problem yourself. Remember to prioritize safety and take your time. If you’re uncomfortable performing any of these repairs, or if the problem persists, don’t hesitate to call a qualified appliance repair technician.
Youtube Video:
Quick Wiring Specifications & Terminal Guide
| Component / Circuit | Standard Wire Gauge | Recommended Protection |
|---|---|---|
| Control & Trigger Signals | 18 – 20 AWG | 5A – 7.5A Inline Fuse |
| Standard Auxiliary Load | 14 – 16 AWG | 15A – 20A Circuit Breaker |
| Main Power Feed / Supply | 10 – 12 AWG | 30A – 40A Heavy-Duty Relay |
Images References
Looking for more diagnostic guides? Explore our complete Washing Machine Problems 3 section for step-by-step troubleshooting solutions.
