Introduction
Discovering standing water in your Kenmore washing machine after a completed cycle is frustrating. This indicates that your Kenmore washing machine does not drain completely, leaving your clothes soaking wet and potentially leading to mildew or unpleasant odors. This issue commonly arises when there’s a blockage in the drain system, a malfunctioning pump, or a problem with the drain hose. Addressing this promptly is essential to prevent further damage to your machine and avoid the inconvenience of repeatedly wet laundry.
💡 Technical Key Takeaways:
- Core Focus: Diagnostic schematic and terminal connection layout for Kenmore Washing Machine Does Not Drain Completely.
- Target Scope: Field technicians, automotive DIYers, and residential/commercial electricians.
- Safety Rule: Always disconnect the primary power source/battery terminal and verify zero voltage with a multimeter before touching wires.
Common Causes of Kenmore Washing Machine Does Not Drain Completely
Here are some of the most frequent reasons your Kenmore washing machine may not be draining properly:
- Clogged Drain Hose: A kinked or blocked drain hose restricts water flow.
- Blocked Drain Pump Filter: Lint, hair, and small objects can accumulate in the drain pump filter, obstructing water drainage.
- Faulty Drain Pump: The drain pump might be malfunctioning or worn out, unable to effectively pump water out of the machine.
- Kinked or Blocked Internal Hoses: Internal hoses connecting the tub to the pump can become kinked or clogged over time.
- Air Lock in the Drain System: Air trapped within the drain system can prevent proper water flow.
- Overloading the Washing Machine: Overfilling the machine can strain the drain system and prevent complete drainage.
- Drain Standpipe Height Issues: If the drain standpipe is too high or too low, it can affect drainage.
- Clogged Tub Drain: Debris can build up inside the internal tub drain, preventing water from flowing to the pump.
- Problem with the Lid Switch: In some models, a malfunctioning lid switch can prevent the drain cycle from initiating.
Symptoms Checklist
Use this checklist to confirm the issue:
- Water remains in the tub after the wash cycle.
- The drain cycle sounds different than usual (e.g., humming, grinding).
- The washing machine displays an error code related to draining.
- Clothes are excessively wet after the spin cycle.
- You can hear water sloshing around inside the machine even when it’s off.
How to Fix Kenmore Washing Machine Does Not Drain Completely Step-by-Step Guide
- Unplug the Washing Machine: For safety, disconnect the washing machine from the power outlet.
- Locate the Drain Hose: The drain hose is typically located at the back of the machine.
- Inspect the Drain Hose for Kinks: Straighten out any kinks or bends in the hose.
- Detach the Drain Hose: Carefully detach the drain hose from the drain standpipe or sink.
- Check for Blockages in the Drain Hose: Flush the hose with water to dislodge any obstructions. You can also use a flexible tool (like a plumbing snake or a straightened coat hanger) to clear the hose.
- Locate the Drain Pump Filter: Consult your Kenmore washing machine manual for the exact location of the drain pump filter. It’s usually at the front, bottom, or back of the machine, behind an access panel.
- Access the Drain Pump Filter: Open the access panel and remove the filter cover (be prepared for some water to spill out; have a towel ready).
- Clean the Drain Pump Filter: Remove any lint, hair, or debris from the filter. Rinse it thoroughly.
- Inspect the Drain Pump: Visually inspect the drain pump area for any visible obstructions.
- Reassemble the Drain Pump Filter: Replace the filter and secure the access panel.
- Reattach the Drain Hose: Reconnect the drain hose to the drain standpipe or sink, ensuring a secure fit.
- Check the Drain Standpipe: Make sure the drain standpipe isn’t clogged. You can use a plumbing snake to clear any blockages.
- Run a Test Cycle: Plug the washing machine back in and run a short wash cycle to see if it drains properly. Observe carefully.
- Check for Error Codes: If the problem persists, check the washing machine’s display panel for any error codes. Consult your manual for code definitions and troubleshooting steps.
Fix the Issue Without Buying Parts
Before considering replacement parts, try these free troubleshooting methods:
- Reset the Washing Machine: Unplug the machine for 1-2 minutes, then plug it back in. This can reset the control panel and clear minor glitches.
- Clean the Washing Machine Regularly: Run an empty wash cycle with washing machine cleaner or a mixture of vinegar and baking soda to prevent build-up of soap scum and debris.
- Check the Water Level Sensor: While harder to access, some issues are related to incorrect water level.
- Inspect Internal Hoses: Visually check accessible internal hoses for kinks or damage. (Unplug the machine first!).
When Replacement Might Be Necessary
If the troubleshooting steps above don’t resolve the issue, the drain pump itself might be faulty and require replacement. A new drain pump typically costs between $50 and $200, depending on the model. Other parts that sometimes fail and lead to drainage issues are the drain hose itself (if cracked) or the water level sensor. However, try all free troubleshooting first.
Safety Warning
- Always unplug the washing machine before attempting any repairs.
- Be careful when handling water, as it can create a slip hazard. Wipe up any spills immediately.
- Consult the manufacturer’s instructions or a qualified technician if you are unsure about any step.
- Do not overload the washing machine.
Tools You May Need
- Screwdrivers (Phillips and flathead)
- Pliers
- Adjustable wrench
- Bucket
- Towels
- Plumbing snake (optional)
FAQ
Here are some frequently asked questions about washing machine drainage issues:
-
Q: Why is my washing machine making a loud humming noise when it tries to drain?
A: This is often a sign that the drain pump is struggling to pump water due to a blockage or a failing motor. Check the drain pump filter first. -
Q: How do I know if my drain pump is bad?
A: If the pump makes unusual noises, doesn’t drain the water, or you see an error code related to draining, the pump may be faulty. -
Q: Can I use bleach to clean my washing machine drain?
A: While bleach can help disinfect, it’s best to use a washing machine cleaner or a vinegar and baking soda mixture to avoid damaging the machine’s components. -
Q: How often should I clean my washing machine drain pump filter?
A: It’s recommended to clean the drain pump filter every 1-3 months, depending on how frequently you use your washing machine.
Conclusion
A Kenmore washing machine that doesn’t drain properly can be a real headache, but with a systematic approach, you can often resolve the issue yourself. Start with the simple checks, and work your way through the troubleshooting steps. If you’ve exhausted all the DIY options and the problem persists, don’t hesitate to call a qualified appliance repair technician for professional assistance. Preventing problems with proper maintenance can extend the machine’s life.
Youtube Video:
Quick Wiring Specifications & Terminal Guide
| Component / Circuit | Standard Wire Gauge | Recommended Protection |
|---|---|---|
| Control & Trigger Signals | 18 – 20 AWG | 5A – 7.5A Inline Fuse |
| Standard Auxiliary Load | 14 – 16 AWG | 15A – 20A Circuit Breaker |
| Main Power Feed / Supply | 10 – 12 AWG | 30A – 40A Heavy-Duty Relay |
Images References
Looking for more diagnostic guides? Explore our complete Washing Machine Problems 4 section for step-by-step troubleshooting solutions.
