Maytag Washer Water Won T Drain


Maytag Washer Water Won T Drain

Introduction

Finding your Maytag washer full of water after a wash cycle is complete is a common and frustrating problem. This can happen after washing a load of clothes, or even during a rinse cycle. A washer that wont drain properly can lead to soggy clothes, potential water damage in your laundry area, and a complete halt to your laundry routine. Addressing this issue quickly is important to prevent mold growth, protect your floors, and get your laundry back on track. Explore more in our Washing Machine Problems 4 collection.

💡 Technical Key Takeaways:

  • Core Focus: Diagnostic schematic and terminal connection layout for Maytag Washer Water Won T Drain.
  • Target Scope: Field technicians, automotive DIYers, and residential/commercial electricians.
  • Safety Rule: Always disconnect the primary power source/battery terminal and verify zero voltage with a multimeter before touching wires.

Common Causes of Maytag Washer Water Won’t Drain

Several factors can prevent your Maytag washer from draining correctly. Here are some of the most common culprits:. For more related activities, check out our My Lg Front Load Washer Won T Turn On.

  • Clogged Drain Hose: The drain hose can become blocked with lint, small items (like socks!), or soap residue.
  • Clogged Drain Pump Filter: Most Maytag washers have a filter to catch debris before it reaches the drain pump. This filter can become clogged, restricting water flow.
  • Drain Pump Malfunction: The drain pump is responsible for pushing the water out of the washer. If it’s faulty, it won’t be able to do its job.
  • Kinked or Blocked Drain Hose: A kink in the drain hose can restrict water flow. Also, make sure the drain pipe where the hose connects isn’t blocked.
  • Lid Switch Issues: Some washers won’t drain if the lid switch is faulty. This switch tells the washer the lid is closed, allowing it to spin and drain.
  • Control Board Problems: In rare cases, a malfunctioning control board can prevent the washer from signaling the drain pump to activate.
  • Air Lock in the Drain Hose: Sometimes air can get trapped in the drain hose, preventing proper drainage.
  • Overuse of Detergent: Too much detergent can lead to excessive suds, which can sometimes interfere with the draining process.

Symptoms Checklist

Use this checklist to accurately identify the issue:

  • Washer is full of water after a wash cycle.
  • Washer makes a humming noise but water doesn’t drain.
  • Washer makes no noise at all during the drain cycle.
  • You find items blocking the drain hose outlet.
  • Error code related to draining appears on the washer’s display (refer to your owner’s manual).
  • The drain hose is visibly kinked or damaged.
  • The water drains very slowly.

How to Fix Maytag Washer Water Won’t Drain Step-by-Step Guide

Follow these steps to troubleshoot your Maytag washer:

  1. Unplug the Washer: For safety, disconnect the washer from the power outlet before starting any troubleshooting.
  2. Locate the Drain Hose: This hose is usually at the back of the washer, connected to a drainpipe or standpipe.
  3. Check the Drain Hose for Kinks: Carefully inspect the entire length of the drain hose for any kinks, bends, or obstructions. Straighten out any kinks you find.
  4. Detach the Drain Hose: Disconnect the drain hose from the drainpipe or standpipe.
  5. Inspect the Drainpipe: Make sure the drainpipe isn’t clogged. You can try running water into it to see if it drains freely.
  6. Flush the Drain Hose: Hold the detached drain hose over a bucket and try flushing it with water from a garden hose or faucet. This will help dislodge any debris inside.
  7. Locate the Drain Pump Filter: This is usually located at the front, bottom of the washer, behind a small access panel. Consult your owner’s manual for the exact location.
  8. Drain Remaining Water: Before removing the filter, place a shallow pan or towel underneath to catch any water that may spill out.
  9. Clean the Drain Pump Filter: Carefully remove the filter (usually by twisting or pulling it out). Clean it thoroughly, removing any lint, debris, or foreign objects.
  10. Reinstall the Drain Pump Filter: Make sure the filter is properly seated and secured before closing the access panel.
  11. Reattach the Drain Hose: Reconnect the drain hose to the drainpipe or standpipe, ensuring a secure fit.
  12. Check the Lid Switch (if applicable): With the washer unplugged, visually inspect the lid switch for damage. If you suspect a problem, consult a technician.
  13. Plug in the Washer: Reconnect the washer to the power outlet.
  14. Run a Test Cycle: Select a spin cycle and start the washer. Observe if the washer drains properly.
  15. If Problem Persists: If the washer still won’t drain, the drain pump itself might be faulty. At this point, consulting a qualified appliance repair technician is recommended.

Fix the Issue Without Buying Parts

Before considering replacement parts, try these free methods:

  • Reset the Washer: Unplug the washer for 1-2 minutes, then plug it back in. This can sometimes reset the control board and resolve minor glitches.
  • Reduce Detergent Use: Using too much detergent can cause excessive suds, hindering drainage. Use the recommended amount specified on the detergent packaging.
  • Regular Cleaning: Run a washer cleaning cycle regularly with a washing machine cleaner to prevent buildup of soap residue and debris.

When Replacement Might Be Necessary

If the above steps don’t resolve the issue, the drain pump is likely faulty and needs to be replaced. A replacement drain pump typically costs between $50 and $150 USD, plus labor costs if you hire a technician. Other parts that might fail, though less commonly, are the lid switch or the control board. Discover more free resources across our collection library.

Safety Warning

  • Always unplug the washer from the power outlet before attempting any repairs.
  • Be careful when handling water, as wet floors can be slippery.
  • If you’re uncomfortable working with electrical appliances, consult a qualified technician.

Tools You May Need

  • Screwdrivers (Phillips and flathead)
  • Pliers
  • Bucket or shallow pan
  • Towels
  • Garden hose (optional)

FAQ

Here are some frequently asked questions:

  • Q: My washer makes a humming noise but doesn’t drain. What does this mean?A: This usually indicates that the drain pump is trying to work but is blocked or faulty. Check the drain pump filter for clogs.
  • Q: How often should I clean the drain pump filter?A: Ideally, clean the filter every 3-6 months, or more frequently if you wash heavily soiled items.
  • Q: Can I use bleach to clean the drain hose?A: It’s generally not recommended, as bleach can damage the hose over time. Use a mild detergent or washing machine cleaner instead.
  • Q: What if my washer has an error code related to draining?A: Consult your owner’s manual to identify the error code and follow the recommended troubleshooting steps.

Conclusion

A washing machine that won’t drain can be a major inconvenience, but often the problem can be resolved with simple troubleshooting steps. By following this guide, you can attempt to fix the issue yourself before calling a technician. Remember to prioritize safety and take your time to carefully inspect each component. Good luck!

Youtube Video:


Quick Wiring Specifications & Terminal Guide

Component / Circuit Standard Wire Gauge Recommended Protection
Control & Trigger Signals 18 – 20 AWG 5A – 7.5A Inline Fuse
Standard Auxiliary Load 14 – 16 AWG 15A – 20A Circuit Breaker
Main Power Feed / Supply 10 – 12 AWG 30A – 40A Heavy-Duty Relay

Images References


Images References, Washing Machine Problems 4

📚 Related Articles

Scroll to Top