2013 Ford Explorer Ac Not Blowing Cold


2013 Ford Explorer Ac Not Blowing Cold

Introduction

There’s nothing worse than a scorching hot day and an AC that’s blowing warm air! If your 2013 Ford Explorer’s AC isn’t blowing cold, it can make driving miserable, especially for families with children or pets. This guide will walk you through some common causes and simple steps to diagnose the problem. Addressing this quickly can prevent further damage and discomfort. Let’s get started!

💡 Technical Key Takeaways:

  • Core Focus: Diagnostic schematic and terminal connection layout for 2013 Ford Explorer Ac Not Blowing Cold.
  • Target Scope: Field technicians, automotive DIYers, and residential/commercial electricians.
  • Safety Rule: Always disconnect the primary power source/battery terminal and verify zero voltage with a multimeter before touching wires.

Common Causes of 2013 Ford Explorer AC Not Blowing Cold

Here are some of the most frequent reasons why your Explorer’s AC might not be cooling properly:

  • Low Refrigerant: The most common cause. Refrigerant is the “coolant” that makes the AC work. A leak can cause it to become low.
  • Refrigerant Leak: Any damage to hoses, seals, or the compressor itself can lead to slow loss of refrigerant
  • Faulty AC Compressor: The compressor is the heart of the AC system. If it fails, it won’t compress the refrigerant properly.
  • Clogged Condenser: The condenser cools the refrigerant. If it’s blocked by debris, it can’t do its job.
  • Bad Condenser Fan: The fan helps cool the condenser. If the fan is not working correctly, the condenser can’t cool effectively
  • Blocked Evaporator Core: The evaporator core cools the air that blows into the cabin. If it’s clogged with dirt or debris, it won’t cool properly.
  • Faulty Blend Door Actuator: This controls the mix of hot and cold air. If it’s stuck, it might be letting in hot air even when the AC is on.
  • Electrical Problems: Issues with fuses, relays, or wiring can prevent the AC compressor from engaging.
  • Broken or Sticking Expansion Valve: The expansion valve controls the flow of refrigerant into the evaporator core. A malfunctioning expansion valve can disrupt the cooling process.
  • Software Glitch: Sometimes, the car’s computer system can have glitches that affect the AC’s operation.

Symptoms Checklist

Use this checklist to accurately identify the problem:

  • AC blows warm air instead of cold air.
  • AC works sometimes, but not consistently.
  • You hear unusual noises (clicking, hissing) when the AC is turned on.
  • The engine overheats when the AC is running.
  • The AC compressor is not engaging (you can’t hear or feel it click on).
  • The cooling fan is not running when the AC is on.
  • There is a visible leak or oily residue near the AC compressor.
  • The AC only works when the car is moving at higher speeds.

How to Fix 2013 Ford Explorer AC Not Blowing Cold Step-by-Step Guide

  1. Start the Engine: Turn on your Ford Explorer and let it idle.
  2. Turn on the AC: Set the AC to the coldest setting and the fan to the highest speed.
  3. Listen for the Compressor: Open the hood and listen for a “click” sound from the AC compressor. This indicates it’s engaging. If you don’t hear it, proceed.
  4. Check the Fuses: Locate the fuse box (usually under the hood or in the passenger compartment check your owner’s manual). Find the fuses for the AC compressor and the blower motor. Inspect them for any signs of damage or burnout. Replace any blown fuses with the correct amperage.
  5. Inspect the AC Compressor Relay: Also in the fuse box, there’s an AC compressor relay. You can try swapping it with an identical relay (like the horn relay) to see if that fixes the problem. If the AC starts working after the swap, the original relay is faulty.
  6. Check the Condenser Fan: With the AC on, make sure the fan in front of the radiator (the condenser fan) is spinning. If it’s not, it could be the fan motor or a related fuse/relay.
  7. Look for Leaks: Visually inspect the AC lines, compressor, and condenser for any signs of leaks. Look for oily residue or dirt accumulation around joints and connections.
  8. Check the Cabin Air Filter: A clogged cabin air filter can restrict airflow and reduce the AC’s cooling efficiency. The cabin air filter is usually located behind the glove box. Remove it and inspect it. Replace it if it’s dirty.
  9. Test the Blend Door Actuator: With the AC on cold, switch the temperature control from cold to hot and back again. Listen for the blend door actuator motor moving behind the dashboard. If you don’t hear anything, it could be faulty.
  10. Check Refrigerant Lines: Look for kinks or damage to the refrigerant lines, especially where they flex or are exposed.
  11. Check the Compressor Clutch Gap: With the engine off, inspect the gap between the compressor clutch and pulley. An excessively large gap can prevent the compressor from engaging. (This requires a feeler gauge and a bit more technical skill.)
  12. Note and Document Write down the step and your finding. This will help you or any mechanic to pinpoint the root cause.

Fix the Issue Without Buying Parts

Before rushing to buy parts, try these free methods:

  • Check and Clean the Condenser: Use a garden hose (gentle spray) to rinse off any debris from the condenser (the radiator-like component in front of the engine).
  • Clean the Evaporator Drain: A clogged evaporator drain can cause moisture buildup and reduce cooling. Locate the drain (usually a small hose sticking out of the firewall) and clear it with a piece of wire.
  • Check Electrical Connectors: Make sure all electrical connectors related to the AC system are securely connected. Clean any corroded connections with electrical contact cleaner.

When Replacement Might Be Necessary

If the above steps don’t fix the problem, you might need to replace a component. Here are some possibilities:. For more related activities, check out our Ac Condenser Unit Freezing Up.

  • AC Compressor: A new compressor can cost between $300 and $800 (plus labor).
  • Condenser: A new condenser can cost between $150 and $400 (plus labor).
  • Evaporator Core: Replacing the evaporator core is labor-intensive and can cost between $500 and $1200.
  • Refrigerant Lines: Replacement lines can vary in price depending on the line.

Safety Warning

  • Always disconnect the negative battery terminal before working on electrical components.
  • Wear safety glasses when working under the hood.
  • Be careful when handling refrigerant. It can cause frostbite. It is illegal to release refrigerants in the atmosphere.
  • If you are uncomfortable working on your car, take it to a qualified mechanic.

Tools You May Need

  • Screwdrivers (Phillips and flathead)
  • Socket set
  • Wrench set
  • Fuse puller
  • Multimeter (optional, for testing electrical components)
  • Feeler gauge (optional, for checking compressor clutch gap)

FAQ

Here are some frequently asked questions about AC problems:

  • Q: Why is my AC blowing warm air only on one side? A: This could be a problem with the blend door actuator.
  • Q: How often should I recharge my AC refrigerant? A: It’s best to have it checked yearly. You only need to recharge if it’s low.
  • Q: Can I recharge my AC myself? A: While DIY kits are available, it’s recommended to have a professional do it to ensure proper levels and leak detection.
  • Q: How do I know if my AC compressor is bad? A: Common symptoms include no cold air, unusual noises, and the compressor not engaging.

Conclusion

Troubleshooting your 2013 Ford Explorer’s AC can seem daunting, but by following these steps, you can hopefully pinpoint the problem and potentially fix it yourself. Remember to be patient and methodical. If you’re still stuck, don’t hesitate to take your Explorer to a trusted mechanic for a professional diagnosis and repair. Good luck, and stay cool!

Quick Wiring Specifications & Terminal Guide

Component / Circuit Standard Wire Gauge Recommended Protection
Control & Trigger Signals 18 – 20 AWG 5A – 7.5A Inline Fuse
Standard Auxiliary Load 14 – 16 AWG 15A – 20A Circuit Breaker
Main Power Feed / Supply 10 – 12 AWG 30A – 40A Heavy-Duty Relay

Images References


Images References, Air Conditioner Troubleshooting 2

Looking for more diagnostic guides? Explore our complete Air Conditioner Troubleshooting 2 section for step-by-step troubleshooting solutions.

📚 Related Articles

Scroll to Top